feliz

Hey Bud! I really apologize as I have not logged onto this site in a LONG time! I would have gotten back to you way earlier. I am guessing you have already finished your kit but just to answer your questions, my paint cost $350 but I used to work for the place that did it. If you're patient though it's not hard to get a great paint job using spray paints. My thighs are held on using a belt and garter system. Hope this helps! Please forgive my LATE reply!

Starting to make some good progress. Kept the end of the barrel bare aluminum rather than painting it. Sent from my iPhone using Tapatalk

Some power cylinder action... Sent from my iPhone using Tapatalk

Range finder mounted Sent from my iPhone using Tapatalk

That's a great vid! Great shots of those weapons! Makes you jealous! To close the holes, I could consider sliding a smaller tube into the blaster of, cutting one into the required size pieces to JB weld behind the holes. Not sure yet which I'll use but it figure it shouldn't be a hard fix. Sent from my iPhone using Tapatalk

Attached the rear stock Sent from my iPhone using Tapatalk

Attached the front barrel. Sent from my iPhone using Tapatalk

Making some progress. Have the two sections back. Have a couple additional small sections to cut out but done for the most part. Attached the mag well from Field Marshal which fits like a glove. May have a weld done additionally to add strength. Sent from my iPhone using Tapatalk

Almost done with the front section. Sent from my iPhone using Tapatalk

A wee bit of progress... Sent from my iPhone using Tapatalk

Appreciate the feedback sir. I'm aware of the base gun and parts used. But I'm not the type of person looking for accuracy down to the screw or millimeter. Just want to make a great version of this and like to be different as well. It'll look great when done regardless of accuracy. It's gunna look great when done though, promise! Sent from my iPhone using Tapatalk

Got a couple more parts for the project. Dropped the pipe off with a friend to machine them. Now to wait. Sent from my iPhone using Tapatalk

Thanks so much for the lead on the rail mounts for the flashlight. that's a good find. For the front barrel, I plan on using hex machine screws and drilling and tapping the main aluminum barrel that I have. Both barrels are with a friend who is machining the holes and slots. I'm kind of on hold now until I get those back and then the fun begins! Sent from my iPhone using Tapatalk

Gunna do lights but not sure about sound yet. I'm going to try to build it so I can add that later if desired. Sent from my iPhone using Tapatalk

Thanks sir. I know they used the airsoft model but I'm not looking for extreme accuracy though. It will look great when I'm done for sure but I just want something that is all metal but still not overweight. And I also want to be different than what else is out there. I'd bet I can get it pretty accurate though if I try. I've seen extremely accurate all aluminum E11 builds and this shouldn't be much much different. Any suggestions or input is welcome though! Sent from my iPhone using Tapatalk

Hey chaos ! Thanks for the reply! I have considered that airsoft version but the issue is that it is a full steel construction which would make it quite heavy. I like the idea of an aluminum version which will be considerably lighter. Wish it were aluminum like their Mauser as I would have jumped on it! Sent from my iPhone using Tapatalk

Although I enjoy my 3D printed E11D blaster, I felt it time to upgrade to an all aluminum build! I've accumulated most of the parts but still need a few more. I have enough to start though. Just to note, I chose not to use the Airsoft version as a base as 1: it is extremely heavy and 2: I want to do something different and all my own. I know there are some who are meticulous about the accuracy of their builds down to the screws and I respect those who do this but be forewarned that if you are one of those, you may not appreciate my build. But, I welcome your feedback! Below are the parts that I have thus far: The magazine well, magazine, power cylinders, ranger finder, Hengstler counter, E11 stock and rear stock adapter are all from Field Marshal (AMAZING PARTS!) I sourced the aluminum tube online and got really lucky in finding an airsoft retractable stock online as well (sadly sold out everywhere) First things I'll be doing is working on the main body and cutting the standard E11 slot for the charging handle and ejection port then on to the front barrel slots. I'll need to find someone to mill down a portion of the front barrel where it attaches the back body to give the illusion that's it's 3 pieces rather than 2. Parts I am missing are the entire handle and trigger housing / assembly and the rear site. If anyone has a lead in metal versions of these I'd be forever grateful! So that's it for now. Will update once progress is made! Sent from my iPhone using Tapatalk

Very much appreciated guys! Sent from my iPhone using Tapatalk

Dude! Looking great! Definitely looking forward to seeing you both at RICC this weekend! Sent from my iPhone using Tapatalk

Mark, this is looking REALLY GOOD! Very well done man! Really looking forward to the final pics! Sent from my iPhone using Tapatalk

Looking good my man! Super psyched to see you making progress in this!!! Looking forward to the finished product!!! Great work! Sent from my iPhone using Tapatalk

Niiiccceee! I feel your excitement!!! BBB day is the best! Open it up already! Sent from my iPad using Tapatalk

Got word today! Approved!!! Yeeehaaawww! Sent from my iPhone using Tapatalk

Sent from my iPhone using Tapatalk

Finally, officially submitted for approval! Cross my fingers!!! Sent from my iPad using Tapatalk