ScottishSith

Slight delay in making this post....The Armory shop reacted brilliantly and super quickly with my replacement shins...they're a much better fit...Which meant there was nothing else to do but get some clearance pictures submitted.......Approval received this afternoon ??? I'm the 1st and at present, the only Deathtrooper in the Imperial Scottish Garrison ???. https://www.flickr.com/gp/194404198@N03/98yP8q

@Lt. Dan, not quite sure how the sizing is off so much, measurements were checked before sending, hopefully things can be rectified quickly...At least if they are slightly oversized there is a chance to alter to make them fit, unfortunately I can't do anything with my shins... Frustrating ! ☹️

The inside of the Armour was a tad rough, so decided to line it all with black spacer mesh, that should protect my undersuit nicely. https://www.flickr.com/gp/194404198@N03/A9QqQ1

Assembled kidney plate and the Thermal detonator. Drilled out the holes on the TD and installed 4mm stainless steel threaded rivets..nice and secure ?? Also added aluminium craft wire to my boot spats, there was a gap in the stitching at the top and bottom of the spat, so cut the wire to length and slid them into place. Now I can shape the boot spats to follow the contour of my boot https://www.flickr.com/gp/194404198@N03/0s2U0f

Assembled the Chest and Backplate armour. Drilled out the pre drilled holes in the Backplate and used Chicago screws and rubber washers to attach the shoulder straps. https://www.flickr.com/gp/194404198@N03/8M87V8

So received my Finished armour kit from the Armory Shop 23/12/21, it arrived well packaged/protected and there where no damaged parts...Man ! Was that box heavy ? All parts were finished really nicely, really impressed with the kit. I only had one issue, my shin armour is too small. When I put my undersuit on and try them on, the left shin will not stay together at all (front or back), the right is slightly larger so the front stays together, but there are large gaps at the back of both shins and there's absolutely no way I can get the top rings on to try and secure the shins. Contacted Denis @ Armory shop to try and get the issue sorted. ??? https://www.flickr.com/gp/194404198@N03/0Z29H4

Its been a great build or should I say assembly of parts so far ?, really looking forward to getting my teeth into the armour assembly when my order arrives from the Armory shop.

My SE14R and E11D Blasters: https://www.flickr.com/gp/194404198@N03/426cK1.

Made my own holster for my SE14R blaster, turned out pretty good ?? https://www.flickr.com/gp/194404198@N03/G4HV17

Added the 2" webbing strap with clip to the inside of my beltset, it feels way more secure with the velcro as back up. Received my Undersuit from the Darkside closet, a great job done on the suit. ?. https://www.flickr.com/gp/194404198@N03/N99mb1

@MKE-Trooper- Yep it's been a very long wait, way more than was initially stated. To be fair, they have had some issues to deal with (painter contracted COVID and the fire in their main workshop), I've reached out to them to ask about my order, but I have still not received any update as to when my order will be ready to ship, pretty disappointing to be honest.

When fitting my Fans to the helmet, I managed to upset one of the helmet LED's, it didn't like being handled and decided to just fall to pieces ? Replaced both LED's and added some frosted plastic diffusion, to get rid of the bright spot in the centre of the green tusk lenses. https://www.flickr.com/photos/194404198@N03/shares/9yn251

Leather Belt pouch (Delta Leather Works): Nice little leather pouch, happy with the quality. One little niggle was the strap on the back, it wasn't cut wide enough and caused the rubber belt to bunch up. So, dismantled the pouch, cut a new length of strap and reassembled the pouch...Looks much better now. https://www.flickr.com/photos/194404198@N03/shares/cerLL7

Beltset (Armory Shop) Pouches and boxes were all good, but the belt that was sent was way too small (105cm instead of the 120cm stated), so sourced belt material and made my own correctly sized belt. Attached boxes, inserted foam into pouches and initially added velcro to fasten the belt. I've since added a snap buckle and 2" webbing strap as my primary means of fastening the belt, with the velcro as added support. https://www.flickr.com/photos/194404198@N03/shares/6WE1m1

OK, I'm up and running with Flickr, so herw goes with my progress up to now: Boots - I initially bought a pair from Imperial boots, very pleased with them, however got the chance to snap up a pair of Dr Marten Talib boots. https://www.flickr.com/gp/194404198@N03/c9G5M9 PS, let me know if the images can be viewed OK.

Armory shop helmet:

Hi Everyone, ScottishSith from the Imperial Scottish Garrison, I've been checking out some of the awsome DT builds on the Spec Ops forum and thought it was time to start my own WIP. Started my build 08/02/21 Here is my current progress: • Helmet (Ordered 01/02/21- Received 24/05/21 ) - Armory Shop. • Armour (Finished set - Ordered 04/03/21 - Received 23/12/21) Armory Shop. • Belt set - (Ordered 14/06/21 - Received 22/06/21) - Armory Shop. • Leather belt pouch - (Ordered 01/07/21 - Received 26/07/21) - Delta Leather Works (Poland) • Undersuit (Ordered 28/02/21 - Received 08/11/21) - Darkside Closet. • Boots: Imperial Boots - Ordered 06/02/21 - Received 01/03/21 Dr Marten Talib boots - Ordered 06/05/21 - Received 12/05/21. • Gloves (Ordered 14/02/21 - Received 22/02/21) - Endorfinders. •SE14R Blaster (Ordered 13/02/21 - Received 04/04/21) - RDR Blasters. • E11-D Blaster (Received) - Imperial Scottish Garrison member ??. • SE14R holster (Complete) - Self made. Pictures for all of the above ? to follow ?... Struggling with the file size of my pictures, so can't upload at the moment. I'll edit and upload a.s.a.p.