Task Force 99: Misty - CRL Discussion

[IcyTrooper[CMD-DL]]

This will be the main listing and we'll tackle each part piece by piece (green is done, yellow is WIP, and red is not finalized):

• Helmet
• Neck Seal
• Under Suit
• Cape
• Shoulder Straps
• Shoulder Armor
• Biceps
• Forearms
• Hand Plates
• Gloves
• Chest Armor
• Back Armor
• Abdomen Armor
• Kidney Armor
• Posterior Armor
• Belt
• Holster
• Thigh Armor
• Lower Leg Armor
• Boots
• DLT-19x Targeting Rifle (Optional)

------------FINALIZED TEXT GOES BELOW THIS LINE------------

Description: SCAR Squadron - Task Force 99: Misty (#59/60)
Prefix: TX
Detachment: Spec Ops Detachment
Context: Star Wars by Marvel Comics

TEXT HERE

For 501st membership only the requirements listed in black need to be met.

Black text indicates a feature that is required for approval. Blue text denotes requirements for Level 2 "Specialist," but is not required for basic approval. Visit the Spec Ops website for a full description of these standards.

Special Notes:

• The armor is gloss white and gloss black in the appropriate spots, or as noted.
• Armor is made from one of these (or similar) types of materials:
  • Fiberglass
  • ABS (Acrylonitrile Butadiene Styrene)
  • HIPS (High Impact Polystyrene).
  • PLA, ABS, PETG (3D Printing)
  • Polyurethane Rubber
• Blasters are not required for legion membership per our weapons policy.
• 3D Printed parts are permitted but all print lines and other artifacts must be removed.

--------------------------------------------

[RAIDER[COTG]]

Thanks @IcyTrooper We can work here @TK-1979

Helmet

Lenses must be sufficiently dark enough to obscure the costumer’s eyes. They are either flat or bubbled. Acceptable colors are black, smoke, or dark green.

The “ear” bars have three or four bumps and are gray or painted gray, with a black outline. Painting the bumps with rank stripes (highlighted) in black is optional.

The frown must have 7 teeth cut out and any coloring must not leave the indented area.

Acceptable color is gray.

Black mesh must be used to obscure the face of the wearer.

The tube stripes are blue or black in color and may number between 9 and 15 per side with the curve bends extending backwards. These can be either hand painted or decals.

Vocoder (vertically ribbed chin detail) is painted black.

The aerators (cylinders on either side of the vocoder) are black, and screening can be either silver or black.

The interior of the aerator can either be white, silver, or black.

Traps (trapezoids on dome of helmet) and tears (area beneath the corners of eye lenses) can be hand painted or decals.

Acceptable color is gray. Rear traps and tears have vertical black lines.

 

OPTIONAL Level two certification (if applicable):

Lenses are bubbled and are dark green.

On the ears there is the presence of 1 screw above the ear bars and no screw below the rank bar. The screw is painted white.

Ear bars have 3 bumps only, not 4.

A black rank stripe is painted on the rear most bump.

There will be 13 black tube stripes per side with the curve bends extending backwards. These can either by hand painted or decals.

-----------------------------------------------------------

Due to the hood, we never get a full look at the helmet.  This shot is about the most exposed we see it:

Considering it's a comic, I think it's safe to say it's a pretty standard TK bucket w/ the same level 2 reqs that we have on Kreel and Cav.  My only question...since those ear bumps aren't ever exposed should those be included in L2 (or L1 for that matter) and would there then have to be some note in the cloak text that the hood fully covers those?