Here is a rough draft of a CRL you can use. It's modified from the Merc's CRL and my own observations from additional screenshots.
Helmet
*Animated style helmet to match visual references is required.
*The dome has a smooth transition into the helmet base without a brow ridge.
*The helmet has embossed lines that outline the upper portion of the visor and extend around the back of the helmet. Additional line details outline the red inverted traingle on the forehead. Two verticle lines extend from the bottom of each earcap and end at the bottom edge of the helmet.
*The bottom mouth portion of the helmet must be recessed from the rest of the face and feature six "teeth", three on each side of the vertical visor section.
*The helmet must feature a black visor that is dark enough to hide the wearer's face. Visor material must be visible in the vertical visor slit of the helmet.
*The helmet must have an inverted red traingle in the center of the helmet dome front.
*The helmet must have two oblong earcaps.
*The left will extend half way down the helmet base and features a small raised circle and one tapered antenna that extends to be level with the top of the helmet dome.
*The right earcap has a cut out facing the back of the helmet. It extends 4/5th of the length of the helmet base. The earcap features a panel line on the front edge. THe earcap features a raised circle detail and two tapering antenna, the front antenna being longer than the rear.
*The back half of the helmet must have a quarter-round rib detail along the bottom edge running from one earcap to the other.
*The helmet must feature a raised rectangular section on the helmets inset back panel. This section must feature three embossed details to match visual references.
*The rear of the helmet must feature two white, two-part decals flanking the raised rear panel detail.
*The helmet dome, faceplate, rear dome, earcaps, mandibles, teeth and rear raised panel must be painted white. The cheeks, rear helmet inset, rear panel detail squares, the area under the earcaps, and the section between the teeth must be light grey. All line details must be black.
*The helmet must be painted and waethered to match visual references.
Flight Suit
*Two piece construction.
*The top will be a form-fitting, long sleeved white shirt, featuring vertical ribbing.
*The shirt will feature red imperial cog with white background patches on each upper bicep.
*Pants must be made of white medium weight material. The pants must be form-fitting. The pants must appear to be a six panel construction to match visual references. This can be accomplished with cosmetic stitching.
*The pants will be tucked neatly into the shin armor.
*The shirt and pants will be weathered to match visual references.
Neck Seal
*The neck seal is constructed from fabric visually matching the shirt material and featuring the same vertical ribbing.
*The neck seal is dark brown to match the gauntlet, shin and hand plates in color.
*The neck seal will come to the wearer's jaw-line in a turtleneck fashion.
Boots
*The boots will be ankle length and will not have any visible vippers, laces or other closure methods.
*White leather or leather like material.
*The sole will be painted white.
*The sole will be flat or may feature a small heal.
Gloves
*White in color
*No seams on the top of the hand.
*Cloth only.
*No straps or closures.
*Will be tucked into the gauntlets.
Hand Plates
*The hand armor must appear to be at least 3mm thick.
*Gauntlets must overlap the bottom edge of the hand plate.
*Any visible gap between the bottom edge of the plate and the gauntlet should be covered with dark brown material or leather to match plate color.
*Feature an embossed inverted triangle.
*Will be painted dark brown with the inverted triangle painted white.
Gauntlets
*The gauntlets will be made of plastic or other rigid material and will appear to be at least 3mm thick.
*The gauntlets must have rounded edges and wrap around the wearer's arm in a seamless appearance.
*The gauntlets feature a protrusion extending slightly past the elbow.
*Both gauntlets must feature an orange and a red button. The orange being on top and the red being on the bottom.
*Must be painted dark brown with white panel ine outlining the elbow protrusion. Must be weathered to match visual references.
Torso Armor
*Imperial style three piece construction, made up of upper and lower abdominal plates and chest plate.
*Must appear to be at least 3mm thick.
*The chest armor will appear to be one piece wrapping from the chest over the shoulders, reaching slightly past the shoulder blades in the rear. Will feature a neck opening just large enough to allow the head to pass through.
*The chest armor features a semi-circle cut out in the center of the front facing lower edge.
*The chest armor will taper vertically resulting in the front being shorter than the back.
*The chest armor will overlap the lower abdominal plate.
*The upper abdominal plate will wrap fully around the wearer and appear to be seamless. (A small seam on the side or back is acceptable).
*The upper abdominal plate will taper vertically so that the front is shorter in the back.
*The upper abdominal plate will feature two semi-circle cutouts, one on the left and one to the right, evenly spaced and lining up with the line detail on the lower abdominal plate.
*The upper abdominal plate will overlap the lower abdominal plate and will fall underneath the chest armor.
*The lower abdominal plate will fall underneath the upper abdominal plate. It will wrap fully wrap around the wearer appearing seamless (a small seam on the side or back is acceptable).
*The lower abdominal plate should be taller in the front than the back to allow the other plates to overlap without a visible gap.
*The lower abdominal plate will feature two sets of vertical embossed lines on the right and left side. These lines will line up with the semi-circle cutouts in the upper plate. Inside the vertical lines will be an embossed rectangle with two line details diving it into thirds.
*Torso armor will be painted white and be weathered to match visual references.
Shoulder armor
*Will appear to be at least 3mm thick.
*Shoulder armor must be an upside down arc shape and should match the curve of the chest armor.
*If the shoulder plate is to be moveable the attchment method must not be visible.
*The shoulder plates will be painted white and be weathered to match visual references.
*Must feature two rectangular strap plates that are attched to the chest piece wrapping over the shoulders.
*The strap plates must appear to be at least 3mm thick and will be painted white.
Belt
*Must be made of plastic or other rigid material (can use leather or other material for the base).
*Must be about six inches wide.
*Must be white and constructed with sixteen plastic rectangular panels and a belt buckel with indented details to match visual references.
*Must include two white tapering hip pouches attached over each hip. The poches must have leather flaps to close the pouch with no visible snaps, velcro, etc.
*Must be weathered to match visual references.
Cod Armor
*Must appear to be at least 3mm thick with rounded edges.
*Triangular shape, tapering into a rounded off point.
*Features embossed line detail down the outside edges and ending in a vertical line 2/3 of the way down the plate.
*Painted white and weathered to match visual references.
Thigh Armor
*Must appear to be at least 3mm thick, with rounded edges.
*Tapering rectangular shape with short wings on either side.
*Front facing wing is longer than the rear facing wing.
*Embossed panel lines seperating the wings from the main panel. The main panel features an embossed rectangle.
*Must be painted white and weathered to match visual references.
Knee Armor
*Must appear to be at least 3mm thick with rounded edges.
*Must attch securely to the shin via a hidden attachment point.
*Must have embossed line details to match visual references.
*Must be painted dark brown with white line detail and weathered to match visual references.
Shin Armor
*Must appear to be at least 3mm thick with rounded edges.
*Shin armor extends down the sides of each foot.
*Must wrap fully around the lower leg and appear to be seamless (small seam on the side or back is acceptable).
*Must be painted dark brown and weathered to match visual references.
Jetpack
*The jetpack must include five main components, Two tapered flanking wing sections, one recessed rectangular plate, one tubular thruster, one small square detail plate.
*Must feature embossed line detailing to match visual references.
*THe wings will be painted white, the thruster and rectangular panel will be dark grey and the aquare detail plate will be orange with light grey details. The jetpack will be weathered to match visual references.
Blaster
*Stock must appear to be telescopic.
*Receiver must have two sets of iron sites. THe rear will be made of two posts and the front will be made of two posts with one circular cap set behind and between the two posts.
*The scope must be mounted in the center of the receiver on a single inverted trapezoid mount. It must have an ocular and objective lense both larger than the main tube.
*The receiver must be square in design with a single barrel protruding from the weapon with an inset barrel housing block.
*The receiver must have an inset rounded square detail on the right and left sides toward the front of the weapon.
*The receiver must have an inset rectangular detail on both sides of the main body of the receiver.
*The receiver must have an inset circle and rectangle detail on both sides of the receiver toward the stock.
*The stock must have an inset circle detail on both sides and an obvious butt pad.
*The pistol grip must be a blocky design and must feature line details that match the visual references.
*The rifle must contain an elongated, rectangular trigger guard.
*The main receiver is painted a dark grey. The secondary details on the receiver, barrel block and scope are a light grey.
*The sight posts, trigger guard, grip, barrel, and stock are black.
*The blaster must be weathered to match visual references.
