nanotek[CMD-DWM] Posted July 22, 2019 Share Posted July 22, 2019 Pending agreement Biceps Finished in a high gloss deep red that matches the colors of the entire costume One on each bicep and are mirror opposites of each other The biceps are made up of two parts; inner and outer bicep One seam that faces forward Overlap towards the inner rear of the bicep Clip greeblie is present low and overlaps the seam There is a small rectangular recessed section just above the clip Two black ovals are present on the outside facing side of the bicep Larger vertical recess towards the rear outer section, intersects where the bicep angles down toward the rear The rear of the bicep has an angular line that drops about 25mm to form a rectangular section when viewed from the rear The rectangular sections have approximately 11 recesses on each bicep The angular sections that meet to form the rectangular sections at the back are flat At the bottom of the rear rectangular section is a black horizontal oblong shaped recess There are vertical recessed lines in the front of the bicep Start at the small rectangular recessed section above the clip greeblie The recesses on the outer bicep terminate at a roughly 33 degree angle The vertical recesses on the inner bicep are roughly angled at 45-47 degrees There are 45-47 degree recessed lines that run around the inner bicep terminate at the front seam and bottom of bicep are overlapped at the inside-back by the rectangular section at the back OPTIONAL Level two certification (if applicable): Clip greeblie is the correct bicep greeblie as per diagram The recessed section above the clip has two steps There are a total of 32 vertical recessed lines at the front that start on the inside of the bicep and end on the outside forming a 'V' shape intersecting at the bicep clip There are a total of 25-30 visible diagonal recessed lines that that start at the front seam and continue around the inside of each bicep disappearing behind the overlap on the inner rear 1 Link to comment
JoeShoe[TX] Posted December 31, 2019 Share Posted December 31, 2019 are we going to specify methods of rigging? other than that, looks good Link to comment
gmrhodes13[501st] Posted January 1, 2020 Share Posted January 1, 2020 We don't see the internal rigging so I would suggest it not be part of the CRL. 1 Link to comment
nanotek[CMD-DWM] Posted January 1, 2020 Author Share Posted January 1, 2020 4 hours ago, JoeShoe said: are we going to specify methods of rigging? other than that, looks good Some of the rigging is visible in the Evolution of the Stormtrooper video, and there is a shot of a display where you can just see the rigging for the bicep. If we do include it, it will be for L2 for sure Link to comment
nanotek[CMD-DWM] Posted May 2, 2020 Author Share Posted May 2, 2020 Ready to finalise @Raider @gmrhodes13 @JoeShoe @rickyboyblue @ukswrath @Blackwatch Link to comment
gmrhodes13[501st] Posted May 2, 2020 Share Posted May 2, 2020 Looks good, found a typo One on each bicepand are mirror opposites of each other One on each bicep and are mirror opposites of each other 1 Link to comment
nanotek[CMD-DWM] Posted May 4, 2020 Author Share Posted May 4, 2020 4 hours ago, Raider said: No line counts for L2? Have not been able to find an asset that will allow me to count them. If anyone has a good 360 of the bicep, that would be helpful. 1 Link to comment
Blackwatch[CMD-DCA] Posted May 11, 2020 Share Posted May 11, 2020 one final pass we will need to double check punctuation and make sure all measurements are updated to the IN(mm) format 1" to form a rectangular section Link to comment
nanotek[CMD-DWM] Posted June 14, 2020 Author Share Posted June 14, 2020 Text moved to main proposal Link to comment
Recommended Posts