PROPOSED MODIFIED CRL- DEL MEEKO- finalized text.

[Blackwatch[CMD-DCA]]

This space will be reserved for finalized text of the Del Meeko Inferno Squad CRL Proposal.  

Items will be posted here for review only when the discussion of each CRL proposal change log has been finalized. 

 

 

Helmet

 The Inferno Squad helmet is modeled after the 3d model specific to Battlefront II game. 

The Rogue One TIE Pilot style helmet is allowed for Basic Approval when requirements outlined below are incorporated. 

Original Trilogy TIE Pilot style helmets are not permitted.  There are no screws visible on the helmet.

Lenses are bubble or flat, are red in color, and must be sufficiently dark enough to obscure the costumer's eyes. Translucent or mirrored red lenses are acceptable.

The front trident area is shorter than a traditional pilot helmet.

There is a rectangular indentation on top of the mohawk above the trident.

There is one retaining clip greeblie in the left side trident indentation. A Nissan retaining clip is most accurate.

The top of the mohawk outside of the raised triangle is painted a dark gun metal color down to  the inside edge of the helmet opening.

There is a pill box just above the back bottom edge of the mohawk. The pill box is the same  black color as the helmet and does not need to be functional.

Spaces between the teeth are cut out and backed with a dark gray or silver mesh material.

The teeth and vocoder are painted flat black.

Oxygen mask connectors are molded into the helmet just in front of the ear caps above the  cheek tubes on both sides of the helmet.

There are Imperial disc greeblies without notches on each ear cap.

There are two painted or decal logos on the forehead of the helmet. The Inferno Squad logo on  the right side and an Imperial cog on the left side.

Logo and Cog are equivalent in size, and shall be between 2.15" (54.6mm) and 2.75" (69.8 mm) for approval. 

There is a red painted or red decal area on the ram’s horn on the right side of the helmet.

There is a red painted or red decal area on the right cheek tube.

There are molded greeblies painted silver inside the hose ports that cover the openings. 

Helmet may have light weathering/ staining. Silver is not permitted.  

A balaclava must be worn when helmet is worn.

 

OPTIONAL Level two certification (if applicable):

Helmet is strictly made from the game's 3D model and correctly sized/scaled to the wearer.  

Hose connectors are made from machined aluminum.

Imperial Cog and Inferno Squad logo will be 2.15" (54.6mm) to 2.25" (57.1mm) scaled to wearer's helmet size. 

Lenses are backed with round-holed mesh/screen.

The pill box is functional.

Lenses are bubble type. 

 

Balaclava

A balaclava is a black head sock/hood that is worn under the helmet and is used primarily to hide any view of the wearer's skin and/or facial hair. 

A balaclava must be worn when the helmet is worn. 

 

[Blackwatch[CMD-DCA]]

Flight Suit

• - One-piece flight suit is made out of canvas or similar heavy material.
• - The front zipper is covered by a 2-inch-wide piece of leather or leather-like material with vertical lines that attaches with Velcro over the zipper.
• - Approximately 1.5" (38.1mm) tall mandarin collar with a chevron shaped, left-over-right Velcro closure.
• A 2.5-inch red embroidered or PVC Inferno Squad emblem, on a black background, is present on both shoulders.
• - The shoulders of the suit are slightly padded.
• - A  compad pocket that properly fits the compad  is placed above the left glove so that the pocket is not hidden, and faces outward on the arm. 
• - On the left bicep below the cog emblem, there is a code cylinder pocket with no flap, and vertical stitching dividing it into pen sleeves.  No code cylinders are present.
• - There is a piece of nylon strapping sewn below the pen sleeve openings and is the same length as the top of the pocket.
• - The bottom front corner of the pocket is cut off at a bevel on the side pointing in view direction, with the broader upside forming the border of the pen sleeves.
• - The right sleeve has a cargo pocket below the cog emblem.
• - The right arm pocket has a chevron flap.
• - Two large chest pockets and two large front pockets with no zippers or flaps are present below the belt
• - There are no leg pockets below the knees.
• - There are two red stripes that run up the right side of the flight suit. The first begins at the bottom of the right leg and continues up to the right armpit. The second begins at the right wrist and stops at the bottom of the arm pocket. The stripe then continues above the arm pocket, behind the patch emblem to the shoulder seam.
• - There are two black stripes that run up the left side of the flight suit. The first begins at the bottom of the left leg and continues up to the left armpit. The second begins at the left wrist and stops at the bottom of the compad pocket. The stripe then continues above the compad pocket up to the bottom edge of the pen sleeves then continues above the pen sleeves, behind the patch emblem to the shoulder seam.
• - There are two black stripes that run up the left side of the flight suit. The first begins at the bottom of the left leg and continues up to the left armpit. The second begins at the left wrist and stops at the bottom of the compad pocket.  The stripe then continues above the compad pocket up to the bottom edge of the pen sleeves then continues above the pen sleeves, behind the patch emblem and up over the shoulder ending at the bottom of the collar.
• - A piece of leather or leather-like material is sewn below the pen sleeve openings and is the same length as the top of the pocket. 
  
  OPTIONAL Level two certification (if applicable):
•  
• + Patches are vinyl on textile with no edge border. If twill is used for the patch material the fabric texture will be vertically oriented. 
  + Textured canvas is most accurate for the flightsuits construction as it is a thick materials with a "solid" structure .  A  "loose",  soft or  lightweight material is not accurate.

[Blackwatch[CMD-DCA]]

Compad

• Rectangular communications pad with patterned painted details matching reference photo.
• Compad is worn with the four large, rectangular buttons pointing towards the wearer’s elbow.  
• Compad is rectangular in shape and fits within the compad pocket window.
• Details of the compad differ from the standard TIE Pilot compad.
• Black buttons are smaller than the red and white buttons; the white button located adjacent to the button with multiple dimples may be a single piece, instead of split in two segments. 
• Compad base color is silver, metallic grey, or weathered silver. 
• Compad size is 2.5"  (63.5mm) x 2" (50mm). 
• Compad is fully visible above the glove, facing outward on the arm. 
• For basic approval (Level 1) a standard TIE pilot style compad painted and worn to match game references may be accepted for use. 
•  
• OPTIONAL Level two certification (if applicable):
  
  Compad  shall be Inferno Squad style with correct button sizes, layout and colors.  Two black buttons at the top of the pad are smaller than the white and red buttons. The white button adjacent to the button with holes/dimples is not split. 
• Compad is moderately weathered / stained. 
• 
  Gauntlet Gloves

  Black, leather or leather-like material, enclosed fingered, non-textured, (normal leather grain/texture/lines are acceptable) fitted gauntlet style.

  No buckles, straps, or decorative stitching.

  There is a split on the bottom gauntlet portion that runs from the glove opening to the wrist that is bridged with leather or leather-like material

•  

   

  - Gloves are made of leather. 
   

[Blackwatch[CMD-DCA]]

NOTE

In editor view I can see all my text lined up perfecdtly but as soon as I hit SAVE the text goes all over the screen.  I have tried to fix this three times.  

 

TACTICAL VEST

The tactical vest is black Cordura nylon.    All straps are black.                                                                                                                                                                   There are a total of fourteen 1" (25mm) wide straps sewn to the tactical vest, with four laying horizonatally on either side of the pouches, and two at the front of each pouch.  Straps are sewn to match reference images.                                                                                                                                                            There are three M4 / M16 magazine pouches, with each filled by a rectangular package covered in the same fabric as the tactical vest.  The packages fill the pouches completely, and extend above the pouch. Each packages has a plastic strip mounted at top facing forward. Strip size is 5/32" x 1/2" to 2 5/8" (4mm x 12mm x 68mm).                                                                                                                                                                                                                            There is a black canvas-covered block on the right side of the vest matching references, with a 1" ( 25mm )wide strip of elastic or webbing mounted to the vest, going across the front of the block.                                                                                                                                                                                                   The main shoulder straps consist of ribbed leather or leather-like material. The front portion of the ribbed shoulder straps measure 1 3/8" (35mm).             The front shoulder strap buckles are tri-glide buckles.                                                                                                                                                                                 Vest-front tri-glides are attached to the vest with 1 3/8" x 1 3/8" (35mm x 35mm) loops. The quick release buckles on the back of the vest are attached  by 1" (25 mm) loops.                                                                                                                                                                                                                                           There is a an approximately 1.5" x 1" (38mm x 25mm) specific buckle greeblie mounted above the tri-glide buckles on each side matching reference images.                                                                                                                                                                                                                                                                 The shoulder straps cross near the top of the back armor box.  Each shoulder strap has a tri-glide that the end of each strap feeds into, near the back armor box shape.  See reference photos and the Costume Gallery for placement.                                                                                                                            There is a 1" (25mm) leather or leather-like waist strap present at the back of the tactical vest, and it is attached to the vest with one quick release buckle on the right  or left side of the vest at the wearers option.  This quick release buckle is hidden under the scout pouch, and is not seen when worn.  A single adjusting tri-glide is centered on the back waist strap.                                                                                                                                                                   The Flyye tactical vest is not accurate and should be avoided.                        

OPTIONAL Level two certification (if applicable):

The vest is fitted to the wearer.                                                                                                                                                                                                                          All vest shoulder and waist straps are made of black leather.                                                                                                                                                              Vest front tri-glides are specific to the games 3d model, and are attached to the vest with 1 3/8" x 1 3/8"(35mm x 35mm) leather loops.                           Game- specific 3d model buckle style greeblies are attached to the leather shoulder straps above the tri-glides. See reference images and the Costume Gallery for placement.                                                                                                                                                                                                                                 Front shoulder straps which go over the shoulder and continue to the back are made of  3 layers of ribbed/ grooved leather strips which are glued/sewed/bonded together.  The first (bottom) layer is 1 3/8" (35mm) with the middle layer added to that. The middle layer shall be 1" (25mm) wide. The final layer is centered on top of the first two layers, and is 9/16" (15mm) wide.  The three bonded strips run the length of the forward portion of the shoulder strap assembly.                                                                                                                                                                                                                                The grooved part of the leather shoulder straps stop just past the wearers shoulders, and continues on as a single 1" (25mm) black leather strap, passing through tri-glides and into specific quick release buckles, which are held to the vest with 1" (25mm) black leather loops.  (see Reference Images and the Costume Gallery for placement and construction.                                                                                                                                                                           The quick-release buckles on the back of the vest, which hold the shoulder straps,  are attached  by 1" (25 mm) black leather loops.                                        The back waist strap has a single quick release buckle mounted to the right side of the vest using 1" (25mm)  black leather loop. This buckle is hidden under the scout style pouch and is not seen when worn.

[Blackwatch[CMD-DCA]]

Shoulder Ammo Pouch

• There is an MP-40 ammo pouch attached to the left shoulder and must be filled.
• The pouch is black in color and made of canvas, or canvas-like material.
• Closure straps are made of black leather or leather-like material.
• There is a small pouch on the bottom of the pouch at the right side. 
  • Pouch stitching is black. 
    
    OPTIONAL Level two certification (if applicable):
    
    Attachment is not seen.  No straps are visible.  Magnets or other source of firm mounting is advised. 
  • Oiler pouch is attached to the bottom right side of the right pouch.

[Blackwatch[CMD-DCA]]

Imperial Officer style Under Belt The belt is constructed from leather or a leather-like material. A very slight texture is acceptable.  Approximately 2" (50.8mm) in width, up to 3" (76.2mm) is acceptable. There are no loops or extra holes on the belt. A single large snap or rivet is visible approximately 1" (25.4mm) from the left side of the buckle. The buckle is constructed from a horizontally brushed metal, or metal looking material. The buckle size is approximately 2 5/8" (66.7mm) high and 4 1/8" (104.5mm) wide with 0.5" (12.7mm)  radius rounded corners. Buckle is adorned with an Imperial Code Disk at the center.

OPTIONAL Level two certification (if applicable): Belt is made of non-textured leather. Two parallel grooves run the length of the belt  1/8" (3.1mm) in from edge.  Snap is worn to the left of the wearer 1" (25mm) from the buckle edge. Buckle has a slight horizontal curve.

[Blackwatch[CMD-DCA]]

Over Belt

•  The over-belt consists of 5 gloss black boxes made of ABS or similar plastic, mounted to a leather or leather like waist strap which closes under the thermal detonator. 
• The waist strap is approximately 1.5" (40mm) wide. 
• The over belt is worn around the under belt, so that the top third of the under belt shows above the ove-rbelt. 
• There are special-shaped boxes on left and right of the 3 central boxes which are horizontal in position as seen in reference photos.
  • A total of 8 rivets are present with 2 rivets mounted vertically on the left and right at the edge of the special-shaped boxes.
• Hanging from the right side of the belt is a hip box made out of hard material. This is connected to the belt by  1.5" (40mm) wide black leather or leather-like straps. The strap is and as long as necessary to allow the box to hang on the wearers right hip.                  For basic L1 approval a standard Scout style hip box may be approved. 
• The strap is attached to the front of the over-belt through a slot on the right side of the central box. The back end of the strap goes behind the under-belt, to the left side of the thermal detonator. 
  • The hip box strap has 1.5" (40mm) quick release buckles on the front and back.  Each buckle is attached at the mid point of the strap. 
  •  

OPTIONAL Level two certification (if applicable):

The  rigid front portion of the outer belt is made from the game's 3d model and scaled to the wearer.                                 The box is smaller than a typical scout box, is curved, the back is closed with a back plate, and features a rectangular depression near the bottom out facing side of the box.                                                                                                                                                                      The boxes may be lightly stained or weathered.  Silver is not permitted.

[Blackwatch[CMD-DCA]]

Scout Style Pouches

Two "scout" style pouches are made of black matte canvas or canvas-like material.                                                                                                                              The  "scout" style pouches are filled to appear full and worn at the back of the belt.                                                                                                                               The pouches will leave sufficient room for the Thermal Detonator mounted between them.                                                                                                                 Pouches may be hung from the tactical vest waist strap, or from the over-belt strap, at the wearers choice.                                                                                    Pouches are a maximum of 6 inches tall, 5 inches wide and 2 inches (152mm tall x 127mm wide and 50.8mm deep). The lower edge of the flap will not be wider than 2 1/2" (63.5mm).                                                                                                                                                                                                                         Pouches are proportional to the size of the wearer and match in-game references. 

OPTIONAL Level two certification (if applicable):

Scout style pouches match in game references.                                                                                                                                                                                            Bottom edge of the pouch flap is less than half the overall width of the pouch.                                                                                                                                       Pouch outer flap has a stitch set back 5/16" (8mm) from the edge.

[Blackwatch[CMD-DCA]]

Again, I am having a lot of trouble getting the text to line up. 

 

Thermal Detonator

Attached to the back of the belt is a rectangular gloss black  Thermal Detonator with a black corrugated hose.  The ends of the hose is covered by gloss black end caps.                                                                                                                                                                                The Thermal detonator fits between the two back belt pouches.                                                                                                                             There are two silver detail greeblies on the central box. These details consist of a dome-shaped greeblie on the left side of the box and rectangular greeblie with  various designs on the right side of the box.                                                                                                          For basic (Level 1) approval a gloss black Shadow Scout style Thermal Detonator with standard greeblies is acceptable, as long as the greeblies are painted silver.

• • OPTIONAL Level two certification (if applicable):
    
    Made from the game's 3d model and scaled to the wearer. 
  • The detonator consists of a boxy central structure containing a ribbed hose, and end caps which are "closed" where the tube enters the end cap.
  • The detonator box features a round dome-shaped greeblie approximately 5/8" (15.8mm) on the left side and a 3/4" x 1.5" (19mm x 32.7mm ) rectangular greeblie featuring various designs as seen in the reference images.
  • The standard shadow scout thermal detonator is not accurate and is not to be used for Level 2 approval. 

[Blackwatch[CMD-DCA]]

• Because of the difficulties I have had above with format, I will leave this set with the extra spacing.  This extra spacing may need to be removed for final CRL use. 
•  
• Holster

• Holster is made of black leather or leather-like material.                                                 A Stormtrooper style holster is acceptable for basic approval.                                Holster is worn on left side of belt.                                                                             Holster is attached via 2 black leather straps which pass behind the belt, using two fasteners in the middle of the belt.                                                                            Fasteners may be rivets, snaps, or Chicago screws.                                                   Note: The straps are slightly longer for this holster then seen on Stormtroopers.There is a retention strap which ends in a point approximately 1/2" (12.7mm) beyond a black snap closure. 

• 
  OPTIONAL Level two certification (if applicable):
•  
• The holster is made of leather. 
• A leather square is seen under the rivet at the top corners of the holster where the straps are mounted. 
• Holster is worn empty.

 

Boots

• Calf high black leather or leather-like material.  Boots are dull in appearance. 
• Similar design to tall German jack boots or tall motorcycle riding boots are acceptable for basic approval.
• Boot has a round, plain toe. Harness style or box toe boots are not to be approved. 
• Ankle straps are to be removed. 
• Typical jackboots are not acceptable as they are too short.  The boot shaft must rise as close to the bottom of the knees as possible.    The boot shall be as tall as required to achieve this appearance.   See reference images. 
• Boots have an adjustment strap on the out facing side of the boot. 
• Adjustment strap has a square, silver adjustment buckle.
• Heels are made of rubber or similar material and may have tread or no tread.
• Boots may contain zipper closure but must be concealed with boot material as to not be visible.
• 
  
   OPTIONAL Level two certification (if applicable):
  
  Boots stops just below wearers knees.  Shaft height should be 15" (38cm) or as required to stop just below the wearers knees.  
• Boots have a flap with adjustment strap with square silver buckle that starts at the middle back of the boot and wraps around to the outfacing sides.  See reference images for shape of the adjustment flap and strap.
  Boots are not shiny, they have a matte appearance.

[Blackwatch[CMD-DCA]]

Face

•  Hair is medium length with a part on the side swooped to the right and brown in color.  
•  Face is clean shaven. Sideburns do not extend past bottom of ear canal. 

[Blackwatch[CMD-DCA]]

Chest Box

• The chest box is required to have the same configurations as seen in the photo.
• The chest box is held to the armor with an invisible system which is not visible when the box is removed.  Strong magnets are advised. 
  The chest box is painted glossy black and matches the sheen of the armor. 
• The chest box has five detail pieces: 1 Red, 1 White, 1 black, 2 Blue. 
• There is a 1/8" (3.1mm) thick white pinstripe border around the square detail pieces.
• There are two round indicator lights above the rocker switches, one white, one red respectively.
• There are three rocker switches below the round indicator lights. The rockers are always gray, white, gray.   The gray rockers have red dots or indicator lamps in the bottom outfacing portion.
• There is a 1/8" (3.1mm) thick white pinstripe that runs horizontally across the bottom portion of the box.
• There is a male silver snap or radio jack and a silver round disc with cone knob greeblie on the lower portion of the box below the horizontal pinstripe.
• There are two "gear" type greeblies affixed to either end of the lower tube portion of the box, and are painted silver or metallic grey. 
• There are two machined aluminum or molded silver greeblies in the hose ports of the box. See reference images and the CRL Gallery view. 
• The hose port greeblies feature 8 round depressions around a raised disc.  The color matches the gear type greeblies. 
• Chestbox may be light to moderately weathered or stained.  Silver is not permitted. 
• The red and white indicator lights and rocker lamps may be functional.

 

OPTIONAL Level two certification (if applicable):

Box is electrically lit to include the red and white squares, both rocker lamp lights and the red and white indicator lights on top of the box. 
Box is based on the games 3d model and is scaled to the wearer and consistent with armor size.

[Blackwatch[CMD-DCA]]

Hoses

Hoses are ribbed rubber 1.25" (31.75mm) in diameter.

There are two plastic (polypropylene, pond hose etc.) or rubber gas mask hoses that run from the helmet ports to the chest box ports. 

Hose length should be proportional to the wearer. 

BlasTech E-11 Based on a real or replica Sterling sub-machine gun, scratch-built, or a modified commercial toy Stormtrooper blaster.

OPTIONAL Level two certification (if applicable): Folding stock (does not need to function). No ammo counter is present. D-ring mounted on the rear. Correct style scope. No power cylinders on the magazine housing. Scratch-built, resin cast, Hyperfirm rubber cast blasters have a total of (7) U shaped channels on blaster (all holes on barrel are covered). If using the popular commercially available Stormtrooper blasters, you shall grind off the T-tracks and replace them with U shaped channels and cover the open rows of holes (total of 7 U shaped channels in all). Correct greeblies on the left rear area are present (door catch and two "hammers")

[Blackwatch[CMD-DCA]]

A DLT-19x is an MG-34 with T-tracks on the barrel, a scope mounted on top of mag loader, red ring around the scope, ejection   port   cover added, and a small disk on the left side, on a real or cast replica of a MG-34 machine gun.                                                                                                                                                                                                                                                   The DLTi19 rifle is scratch-built or is a high-end prop replica which matches reference images.

OPTIONAL Level two certification (if applicable):

Accurate MG-34 replica base using correct size and proportions,  either cast or 3d printed from an original MG-34.                                                                                                                             The scope has a design specific to the game's 3D model, and has a red ring which matches reference images for placement and size.                                                                                          Scope should include real glass lenses.    

[Blackwatch[CMD-DCA]]

Thermal Detonator

Detonator is a handheld sphere that is chrome silver in color.

The Detonator is worn on the right front of the Over Belt, and is worn to the right of the Detonite Charge if that is worn.

Asymmetric latitudinal lines are etched into the reflective silver body of the detonator.

Detonator appears to be open like a puzzle, creating a trench around the circumference of the sphere.

Three front activation indicators are visible within center band.

A light grey ovular and contoured top thumb switch is seen with a raised grip surface.

Detonator has the appearance of an inset red arming indicator, functional or non-functional on top in front of the thumb switch.

 

OPTIONAL Level two certification (if applicable):
Thumb switch activates the detonator.

Switch slides back to reveal a lit red arming light.

The three front activation indicators light up and flash based on visual references.

The official Star Wars LFL licensed Thermal Detonator sold as the "hot potato" game should be allowed for Level 2 because it meets the criteria listed above. 

 

Detonite Charge 

The Detonite charge is grey , olive olive -grey or olive drab in color and hangs from the scout belt with a fastener that is not seen.  

The Detonite Charge  is worn on the right front of the Over Belt, and is worn to the left of the Thermal Detonator  if that is worn.

The Detonite Charge is a cylindrical explosive which has a flanged base extending outwards from the bottom of the cylinder. The base  stops 1/4 of the way up the cylinder. 

Mounted onto the cylindrical part of the charge are two square "vent" greeblies  which feature mounting tabs held on with four domed-head wood screws. 

The top of the charge is depressed 3/8" (9.5mm) and features various greeblies mounted around a central core which rises above the top rim of the cylinder.  Inside the depressed area are several rectangular greeblies as well as two silver raised knurled thumbscrews. 

The "core" has a silver raised cylindrical "pipe" fitting with a groove running all the way around it.   

The flange around the base has a total of 36 depressions or holes in groups of 9 spaced equally around the diameter. Hole diameter will not exceed 1/8" (3.1mm).

The open area of the flanged base features various designs and greeblies which match screen references.

The charge may be scratch built, cast, printed or high end prop replica. 

There is a 1" (25mm) red or brown-red ring which runs around the charge where the flange meets the cylinder.  There are two yellow or ochre-colored rectangular stripes which divide the red ring into two segments.  These yellow stripes are situated between the middle of the cylinder height, and stop 1/4" (6.35mm) above the bottom of the flange.  There may be two different designs in the yellow stripes which match screen images. 

OPTIONAL Level two certification (if applicable):

Detonite charge is made from the games 3d model and matches game references including color and markings. 

The detonite charge is electrically lit and feature sound effects when 'activated'.

The black markings on the yellow stripes match the markings seen in game.

[RAIDER[COTG]]

Corrected bullets and spacing @Blackwatch @MahXPrime @TX-20113  Check the bullets though if any need to be indented as sub-bullets.

Helmet

•  The Inferno Squad helmet is modeled after the 3d model specific to Battlefront II game. 
• The Rogue One TIE Pilot style helmet is allowed for Basic Approval when requirements outlined below are incorporated. 
• Original Trilogy TIE Pilot style helmets are not permitted.  There are no screws visible on the helmet.
• Lenses are bubble or flat, are red in color, and must be sufficiently dark enough to obscure the costumer's eyes. Translucent or mirrored red lenses are acceptable.
• The front trident area is shorter than a traditional pilot helmet.
• There is a rectangular indentation on top of the mohawk above the trident.
• There is one retaining clip greeblie in the left side trident indentation. A Nissan retaining clip is most accurate.
• The top of the mohawk outside of the raised triangle is painted a dark gun metal color down to  the inside edge of the helmet opening.
• There is a pill box just above the back bottom edge of the mohawk. The pill box is the same  black color as the helmet and does not need to be functional.
• Spaces between the teeth are cut out and backed with a dark gray or silver mesh material.
• The teeth and vocoder are painted flat black.
• Oxygen mask connectors are molded into the helmet just in front of the ear caps above the  cheek tubes on both sides of the helmet.
• There are Imperial disc greeblies without notches on each ear cap.
• There are two painted or decal logos on the forehead of the helmet. The Inferno Squad logo on  the right side and an Imperial cog on the left side.
• Logo and Cog are equivalent in size, and shall be between 2.15" (54.6mm) and 2.75" (69.8 mm) for approval. 
• There is a red painted or red decal area on the ram’s horn on the right side of the helmet.
• There is a red painted or red decal area on the right cheek tube.
• There are molded greeblies painted silver inside the hose ports that cover the openings. 
• Helmet may have light weathering/ staining. Silver is not permitted.  
• A balaclava must be worn when helmet is worn.

OPTIONAL Level two certification (if applicable):

• Helmet is strictly made from the game's 3D model and correctly sized/scaled to the wearer.  
• Hose connectors are made from machined aluminum.
• Imperial Cog and Inferno Squad logo will be 2.15" (54.6mm) to 2.25" (57.1mm) scaled to wearer's helmet size. 
• Lenses are backed with round-holed mesh/screen.
• The pill box is functional.
• Lenses are bubble type. 

 

Balaclava

• A balaclava is a black head sock/hood that is worn under the helmet and is used primarily to hide any view of the wearer's skin and/or facial hair. 
• A balaclava must be worn when the helmet is worn.

 

Flight Suit

• One-piece flight suit is made out of canvas or similar heavy material.
• The front zipper is covered by a 2-inch-wide piece of leather or leather-like material with vertical lines that attaches with Velcro over the zipper.
• Approximately 1.5" (38.1mm) tall mandarin collar with a chevron shaped, left-over-right Velcro closure.
• A 2.5-inch red embroidered or PVC Inferno Squad emblem, on a black background, is present on both shoulders.
• The shoulders of the suit are slightly padded.
• A  compad pocket that properly fits the compad  is placed above the left glove so that the pocket is not hidden, and faces outward on the arm. 
• On the left bicep below the cog emblem, there is a code cylinder pocket with no flap, and vertical stitching dividing it into pen sleeves.  No code cylinders are present.
• There is a piece of nylon strapping sewn below the pen sleeve openings and is the same length as the top of the pocket.
• The bottom front corner of the pocket is cut off at a bevel on the side pointing in view direction, with the broader upside forming the border of the pen sleeves.
• The right sleeve has a cargo pocket below the cog emblem.
• The right arm pocket has a chevron flap.
• Two large chest pockets and two large front pockets with no zippers or flaps are present below the belt
• There are no leg pockets below the knees.
• There are two red stripes that run up the right side of the flight suit. The first begins at the bottom of the right leg and continues up to the right armpit. The second begins at the right wrist and stops at the bottom of the arm pocket. The stripe then continues above the arm pocket, behind the patch emblem to the shoulder seam.
• There are two black stripes that run up the left side of the flight suit. The first begins at the bottom of the left leg and continues up to the left armpit. The second begins at the left wrist and stops at the bottom of the compad pocket. The stripe then continues above the compad pocket up to the bottom edge of the pen sleeves then continues above the pen sleeves, behind the patch emblem to the shoulder seam.
• There are two black stripes that run up the left side of the flight suit. The first begins at the bottom of the left leg and continues up to the left armpit. The second begins at the left wrist and stops at the bottom of the compad pocket.  The stripe then continues above the compad pocket up to the bottom edge of the pen sleeves then continues above the pen sleeves, behind the patch emblem and up over the shoulder ending at the bottom of the collar.
• A piece of leather or leather-like material is sewn below the pen sleeve openings and is the same length as the top of the pocket. 

OPTIONAL Level two certification (if applicable):

• Patches are vinyl on textile with no edge border. If twill is used for the patch material the fabric texture will be vertically oriented. 
• Textured canvas is most accurate for the flightsuits construction as it is a thick materials with a "solid" structure .  A  "loose",  soft or  lightweight material is not accurate.

 

Compad

• Rectangular communications pad with patterned painted details matching reference photo.
• Compad is worn with the four large, rectangular buttons pointing towards the wearer’s elbow.  
• Compad is rectangular in shape and fits within the compad pocket window.
• Details of the compad differ from the standard TIE Pilot compad.
• Black buttons are smaller than the red and white buttons; the white button located adjacent to the button with multiple dimples may be a single piece, instead of split in two segments. 
• Compad base color is silver, metallic grey, or weathered silver. 
• Compad size is 2.5"  (63.5mm) x 2" (50mm). 
• Compad is fully visible above the glove, facing outward on the arm. 
• For basic approval (Level 1) a standard TIE pilot style compad painted and worn to match game references may be accepted for use.

OPTIONAL Level two certification (if applicable):

• Compad  shall be Inferno Squad style with correct button sizes, layout and colors.  Two black buttons at the top of the pad are smaller than the white and red buttons. The white button adjacent to the button with holes/dimples is not split. 
• Compad is moderately weathered / stained.

Gauntlet Gloves

• Black, leather or leather-like material, enclosed fingered, non-textured, (normal leather grain/texture/lines are acceptable) fitted gauntlet style.
• No buckles, straps, or decorative stitching.
• There is a split on the bottom gauntlet portion that runs from the glove opening to the wrist that is bridged with leather or leather-like material
• Gloves are made of leather. Is this supposed to be Level 2?

 

TACTICAL VEST

• The tactical vest is black Cordura nylon.
• All straps are black.
• There are a total of fourteen 1" (25mm) wide straps sewn to the tactical vest, with four laying horizonatally on either side of the pouches, and two at the front of each pouch.  Straps are sewn to match reference images.
• There are three M4 / M16 magazine pouches, with each filled by a rectangular package covered in the same fabric as the tactical vest.  The packages fill the pouches completely, and extend above the pouch. Each packages has a plastic strip mounted at top facing forward. Strip size is 5/32" x 1/2" to 2 5/8" (4mm x 12mm x 68mm).             
• There is a black canvas-covered block on the right side of the vest matching references, with a 1" ( 25mm )wide strip of elastic or webbing mounted to the vest, going across the front of the block.
• The main shoulder straps consist of ribbed leather or leather-like material. The front portion of the ribbed shoulder straps measure 1 3/8" (35mm).
• The front shoulder strap buckles are tri-glide buckles.
• Vest-front tri-glides are attached to the vest with 1 3/8" x 1 3/8" (35mm x 35mm) loops. The quick release buckles on the back of the vest are attached  by 1" (25 mm) loops. 
• There is a an approximately 1.5" x 1" (38mm x 25mm) specific buckle greeblie mounted above the tri-glide buckles on each side matching reference images.
• The shoulder straps cross near the top of the back armor box.  Each shoulder strap has a tri-glide that the end of each strap feeds into, near the back armor box shape.  See reference photos and the Costume Gallery for placement.
• There is a 1" (25mm) leather or leather-like waist strap present at the back of the tactical vest, and it is attached to the vest with one quick release buckle on the right  or left side of the vest at the wearers option.  This quick release buckle is hidden under the scout pouch, and is not seen when worn.  A single adjusting tri-glide is centered on the back waist strap.
• The Flyye tactical vest is not accurate and should be avoided.                        

OPTIONAL Level two certification (if applicable):

• The vest is fitted to the wearer.
• All vest shoulder and waist straps are made of black leather.
• Vest front tri-glides are specific to the games 3d model, and are attached to the vest with 1 3/8" x 1 3/8"(35mm x 35mm) leather loops.
• Game- specific 3d model buckle style greeblies are attached to the leather shoulder straps above the tri-glides. See reference images and the Costume Gallery for placement.
• Front shoulder straps which go over the shoulder and continue to the back are made of  3 layers of ribbed/ grooved leather strips which are glued/sewed/bonded together.  The first (bottom) layer is 1 3/8" (35mm) with the middle layer added to that. The middle layer shall be 1" (25mm) wide. The final layer is centered on top of the first two layers, and is 9/16" (15mm) wide.  The three bonded strips run the length of the forward portion of the shoulder strap assembly.
• The grooved part of the leather shoulder straps stop just past the wearers shoulders, and continues on as a single 1" (25mm) black leather strap, passing through tri-glides and into specific quick release buckles, which are held to the vest with 1" (25mm) black leather loops.  (see Reference Images and the Costume Gallery for placement and construction.           
• The quick-release buckles on the back of the vest, which hold the shoulder straps,  are attached  by 1" (25 mm) black leather loops.
• The back waist strap has a single quick release buckle mounted to the right side of the vest using 1" (25mm)  black leather loop. This buckle is hidden under the scout style pouch and is not seen when worn.

 

Shoulder Ammo Pouch

• There is an MP-40 ammo pouch attached to the left shoulder and must be filled.
• The pouch is black in color and made of canvas, or canvas-like material.
• Closure straps are made of black leather or leather-like material.
• There is a small pouch on the bottom of the pouch at the right side. 
• Pouch stitching is black. 

OPTIONAL Level two certification (if applicable):

• Attachment is not seen.  No straps are visible.  Magnets or other source of firm mounting is advised. 
• Oiler pouch is attached to the bottom right side of the right pouch.

 

Imperial Officer Under Belt

• The belt is constructed from leather or a leather-like material. A very slight texture is acceptable. 
• Approximately 2" (50.8mm) in width, up to 3" (76.2mm) is acceptable.
• There are no loops or extra holes on the belt.
• A single large snap or rivet is visible approximately 1" (25.4mm) from the left side of the buckle.
• The buckle is constructed from a horizontally brushed metal, or metal looking material.
• The buckle size is approximately 2 5/8" (66.7mm) high and 4 1/8" (104.5mm) wide with 0.5" (12.7mm)  radius rounded corners.
• Buckle is adorned with an Imperial Code Disk at the center.

OPTIONAL Level two certification (if applicable):

• Belt is made of non-textured leather.
• Two parallel grooves run the length of the belt  1/8" (3.1mm) in from edge. 
• Snap is worn to the left of the wearer 1" (25mm) from the buckle edge.
• Buckle has a slight horizontal curve.

 

Over Belt

•  The over-belt consists of 5 gloss black boxes made of ABS or similar plastic, mounted to a leather or leather like waist strap which closes under the thermal detonator. 
• The waist strap is approximately 1.5" (40mm) wide. 
• The over belt is worn around the under belt, so that the top third of the under belt shows above the ove-rbelt. 
• There are special-shaped boxes on left and right of the 3 central boxes which are horizontal in position as seen in reference photos.
• A total of 8 rivets are present with 2 rivets mounted vertically on the left and right at the edge of the special-shaped boxes.
• Hanging from the right side of the belt is a hip box made out of hard material. This is connected to the belt by  1.5" (40mm) wide black leather or leather-like straps. The strap is and as long as necessary to allow the box to hang on the wearers right hip.
• For basic L1 approval a standard Scout style hip box may be approved. 
• The strap is attached to the front of the over-belt through a slot on the right side of the central box. The back end of the strap goes behind the under-belt, to the left side of the thermal detonator. 
• The hip box strap has 1.5" (40mm) quick release buckles on the front and back.  Each buckle is attached at the mid point of the strap.

 

OPTIONAL Level two certification (if applicable):

• The  rigid front portion of the outer belt is made from the game's 3d model and scaled to the wearer.
• The box is smaller than a typical scout box, is curved, the back is closed with a back plate, and features a rectangular depression near the bottom out facing side of the box.               
• The boxes may be lightly stained or weathered.  Silver is not permitted.

 

Scout Style Pouches

• Two "scout" style pouches are made of black matte canvas or canvas-like material.
• The  "scout" style pouches are filled to appear full and worn at the back of the belt.
• The pouches will leave sufficient room for the Thermal Detonator mounted between them.
• Pouches may be hung from the tactical vest waist strap, or from the over-belt strap, at the wearers choice.
• Pouches are a maximum of 6 inches tall, 5 inches wide and 2 inches (152mm tall x 127mm wide and 50.8mm deep). The lower edge of the flap will not be wider than 2 1/2" (63.5mm).
• Pouches are proportional to the size of the wearer and match in-game references. 

OPTIONAL Level two certification (if applicable):

• Scout style pouches match in game references.
• Bottom edge of the pouch flap is less than half the overall width of the pouch.
• Pouch outer flap has a stitch set back 5/16" (8mm) from the edge.

 

Thermal Detonator

• Attached to the back of the belt is a rectangular gloss black  Thermal Detonator with a black corrugated hose.  The ends of the hose is covered by gloss black end caps.
• The Thermal detonator fits between the two back belt pouches.
• There are two silver detail greeblies on the central box. These details consist of a dome-shaped greeblie on the left side of the box and rectangular greeblie with  various designs on the right side of the box.
• For basic (Level 1) approval a gloss black Shadow Scout style Thermal Detonator with standard greeblies is acceptable, as long as the greeblies are painted silver.

OPTIONAL Level two certification (if applicable):

• Made from the game's 3d model and scaled to the wearer. 
• The detonator consists of a boxy central structure containing a ribbed hose, and end caps which are "closed" where the tube enters the end cap.
• The detonator box features a round dome-shaped greeblie approximately 5/8" (15.8mm) on the left side and a 3/4" x 1.5" (19mm x 32.7mm ) rectangular greeblie featuring various designs as seen in the reference images.
• The standard shadow scout thermal detonator is not accurate and is not to be used for Level 2 approval.

 

Holster

• Holster is made of black leather or leather-like material.
• A Stormtrooper style holster is acceptable for basic approval.
• Holster is worn on left side of belt.
• Holster is attached via 2 black leather straps which pass behind the belt, using two fasteners in the middle of the belt.
• Fasteners may be rivets, snaps, or Chicago screws.
• Note: The straps are slightly longer for this holster then seen on Stormtroopers.There is a retention strap which ends in a point approximately 1/2" (12.7mm) beyond a black snap closure. 

OPTIONAL Level two certification (if applicable):

• The holster is made of leather. 
• A leather square is seen under the rivet at the top corners of the holster where the straps are mounted. 
• Holster is worn empty.

 

Boots

• Calf high black leather or leather-like material.  Boots are dull in appearance. 
• Similar design to tall German jack boots or tall motorcycle riding boots are acceptable for basic approval.
• Boot has a round, plain toe. Harness style or box toe boots are not to be approved. 
• Ankle straps are to be removed. 
• Typical jackboots are not acceptable as they are too short.  The boot shaft must rise as close to the bottom of the knees as possible.  The boot shall be as tall as required to achieve this appearance.   See reference images. 
• Boots have an adjustment strap on the out facing side of the boot. 
• Adjustment strap has a square, silver adjustment buckle.
• Heels are made of rubber or similar material and may have tread or no tread.
• Boots may contain zipper closure but must be concealed with boot material as to not be visible.

 OPTIONAL Level two certification (if applicable):

• Boots stops just below wearers knees.  Shaft height should be 15" (38cm) or as required to stop just below the wearers knees.  
• Boots have a flap with adjustment strap with square silver buckle that starts at the middle back of the boot and wraps around to the outfacing sides.  See reference images for shape of the adjustment flap and strap.
• Boots are not shiny, they have a matte appearance.

 

Face

• Hair is medium length with a part on the side swooped to the right and brown in color.
• Face is clean shaven. Sideburns do not extend past bottom of ear canal.

 

Chest Box

• The chest box is required to have the same configurations as seen in the photo.
• The chest box is held to the armor with an invisible system which is not visible when the box is removed.  Strong magnets are advised. 
• The chest box is painted glossy black and matches the sheen of the armor. 
• The chest box has five detail pieces: 1 Red, 1 White, 1 black, 2 Blue. 
• There is a 1/8" (3.1mm) thick white pinstripe border around the square detail pieces.
• There are two round indicator lights above the rocker switches, one white, one red respectively.
• There are three rocker switches below the round indicator lights. The rockers are always gray, white, gray.   The gray rockers have red dots or indicator lamps in the bottom outfacing portion.
• There is a 1/8" (3.1mm) thick white pinstripe that runs horizontally across the bottom portion of the box.
• There is a male silver snap or radio jack and a silver round disc with cone knob greeblie on the lower portion of the box below the horizontal pinstripe.
• There are two "gear" type greeblies affixed to either end of the lower tube portion of the box, and are painted silver or metallic grey. 
• There are two machined aluminum or molded silver greeblies in the hose ports of the box. See reference images and the CRL Gallery view. 
• The hose port greeblies feature 8 round depressions around a raised disc.  The color matches the gear type greeblies. 
• Chestbox may be light to moderately weathered or stained.  Silver is not permitted. 
• The red and white indicator lights and rocker lamps may be functional.

OPTIONAL Level two certification (if applicable):

• Box is electrically lit to include the red and white squares, both rocker lamp lights and the red and white indicator lights on top of the box. 
• Box is based on the games 3d model and is scaled to the wearer and consistent with armor size.

 

Hoses

• Hoses are ribbed rubber 1.25" (31.75mm) in diameter.
• There are two plastic (polypropylene, pond hose etc.) or rubber gas mask hoses that run from the helmet ports to the chest box ports. 
• Hose length should be proportional to the wearer. 

 

BlasTech E-11

• Based on a real or replica Sterling sub-machine gun, scratch-built, or a modified commercial toy Stormtrooper blaster.

OPTIONAL Level two certification (if applicable):

• Folding stock (does not need to function).
• No ammo counter is present.
• D-ring mounted on the rear.
• Correct style scope.
• No power cylinders on the magazine housing.
• Scratch-built, resin cast, Hyperfirm rubber cast blasters have a total of (7) U shaped channels on blaster (all holes on barrel are covered).
• If using the popular commercially available Stormtrooper blasters, you shall grind off the T-tracks and replace them with U shaped channels and cover the open rows of holes (total of 7 U shaped channels in all).
• Correct greeblies on the left rear area are present (door catch and two "hammers").

 

DLT-19x

A DLT-19x is an MG-34 with T-tracks on the barrel, a scope mounted on top of mag loader, red ring around the scope, ejection port cover added, and a small disk on the left side, on a real or cast replica of a MG-34 machine gun.

• The DLT-19x rifle is scratch-built or is a high-end prop replica which matches reference images.

OPTIONAL Level two certification (if applicable):

• Accurate MG-34 replica base using correct size and proportions,  either cast or 3d printed from an original MG-34.                                                                                                        
• The scope has a design specific to the game's 3D model, and has a red ring which matches reference images for placement and size.                                                                       
• Scope should include real glass lenses.    

 

Thermal Detonator

• Detonator is a handheld sphere that is chrome silver in color.
• The Detonator is worn on the right front of the Over Belt, and is worn to the right of the Detonite Charge if that is worn.
• Asymmetric latitudinal lines are etched into the reflective silver body of the detonator.
• Detonator appears to be open like a puzzle, creating a trench around the circumference of the sphere.
• Three front activation indicators are visible within center band.
• A light grey ovular and contoured top thumb switch is seen with a raised grip surface.
• Detonator has the appearance of an inset red arming indicator, functional or non-functional on top in front of the thumb switch.

OPTIONAL Level two certification (if applicable):

• Thumb switch activates the detonator.
• Switch slides back to reveal a lit red arming light.
• The three front activation indicators light up and flash based on visual references.
• The official Star Wars LFL licensed Thermal Detonator sold as the "hot potato" game should be allowed for Level 2 because it meets the criteria listed above.

 

Detonite Charge 

• The Detonite charge is grey , olive olive -grey or olive drab in color and hangs from the scout belt with a fastener that is not seen.  
• The Detonite Charge  is worn on the right front of the Over Belt, and is worn to the left of the Thermal Detonator  if that is worn.
• The Detonite Charge is a cylindrical explosive which has a flanged base extending outwards from the bottom of the cylinder. The base  stops 1/4 of the way up the cylinder. 
• Mounted onto the cylindrical part of the charge are two square "vent" greeblies  which feature mounting tabs held on with four domed-head wood screws. 
• The top of the charge is depressed 3/8" (9.5mm) and features various greeblies mounted around a central core which rises above the top rim of the cylinder.  Inside the depressed area are several rectangular greeblies as well as two silver raised knurled thumbscrews. 
• The "core" has a silver raised cylindrical "pipe" fitting with a groove running all the way around it.   
• The flange around the base has a total of 36 depressions or holes in groups of 9 spaced equally around the diameter. Hole diameter will not exceed 1/8" (3.1mm).
• The open area of the flanged base features various designs and greeblies which match screen references.
• The charge may be scratch built, cast, printed or high end prop replica. 
• There is a 1" (25mm) red or brown-red ring which runs around the charge where the flange meets the cylinder.  There are two yellow or ochre-colored rectangular stripes which divide the red ring into two segments.  These yellow stripes are situated between the middle of the cylinder height, and stop 1/4" (6.35mm) above the bottom of the flange.  There may be two different designs in the yellow stripes which match screen images. 

OPTIONAL Level two certification (if applicable):

• Detonite charge is made from the games 3d model and matches game references including color and markings. 
• The detonite charge is electrically lit and feature sound effects when 'activated'.
• The black markings on the yellow stripes match the markings seen in game.

[TX-20113[501st]]

4 hours ago, Raider said:

Gloves are made of leather. Is this supposed to be Level 2?

Yes, why not ? i would agree

4 hours ago, Raider said:

Corrected bullets and spacing @Blackwatch @MahXPrime @TX-20113  Check the bullets though if any need to be indented as sub-bullets.

Helmet

•  The Inferno Squad helmet is modeled after the 3d model specific to Battlefront II game. 
• The Rogue One TIE Pilot style helmet is allowed for Basic Approval when requirements outlined below are incorporated. 
• Original Trilogy TIE Pilot style helmets are not permitted.  There are no screws visible on the helmet.
• Lenses are bubble or flat, are red in color, and must be sufficiently dark enough to obscure the costumer's eyes. Translucent or mirrored red lenses are acceptable.
• The front trident area is shorter than a traditional pilot helmet.
• There is a rectangular indentation on top of the mohawk above the trident.
• There is one retaining clip greeblie in the left side trident indentation. A Nissan retaining clip is most accurate.
• The top of the mohawk outside of the raised triangle is painted a dark gun metal color down to  the inside edge of the helmet opening.
• There is a pill box just above the back bottom edge of the mohawk. The pill box is the same  black color as the helmet and does not need to be functional.
• Spaces between the teeth are cut out and backed with a dark gray or silver mesh material.
• The teeth and vocoder are painted flat black.
• Oxygen mask connectors are molded into the helmet just in front of the ear caps above the  cheek tubes on both sides of the helmet.
• There are Imperial disc greeblies without notches on each ear cap.
• There are two painted or decal logos on the forehead of the helmet. The Inferno Squad logo on  the right side and an Imperial cog on the left side.
• Logo and Cog are equivalent in size, and shall be between 2.15" (54.6mm) and 2.75" (69.8 mm) for approval. 
• There is a red painted or red decal area on the ram’s horn on the right side of the helmet.
• There is a red painted or red decal area on the right cheek tube.
• There are molded greeblies painted silver inside the hose ports that cover the openings. 
• Helmet may have light weathering/ staining. Silver is not permitted.  
• A balaclava must be worn when helmet is worn.

OPTIONAL Level two certification (if applicable):

• Helmet is strictly made from the game's 3D model and correctly sized/scaled to the wearer.  
• Hose connectors are made from machined aluminum.
• Imperial Cog and Inferno Squad logo will be 2.15" (54.6mm) to 2.25" (57.1mm) scaled to wearer's helmet size. 
• Lenses are backed with round-holed mesh/screen.
• The pill box is functional.
• Lenses are bubble type. 

 

Balaclava

• A balaclava is a black head sock/hood that is worn under the helmet and is used primarily to hide any view of the wearer's skin and/or facial hair. 
• A balaclava must be worn when the helmet is worn.

 

Flight Suit

• One-piece flight suit is made out of canvas or similar heavy material.
• The front zipper is covered by a 2-inch-wide piece of leather or leather-like material with vertical lines that attaches with Velcro over the zipper.
• Approximately 1.5" (38.1mm) tall mandarin collar with a chevron shaped, left-over-right Velcro closure.
• A 2.5-inch red embroidered or PVC Inferno Squad emblem, on a black background, is present on both shoulders.
• The shoulders of the suit are slightly padded.
• A  compad pocket that properly fits the compad  is placed above the left glove so that the pocket is not hidden, and faces outward on the arm. 
• On the left bicep below the cog emblem, there is a code cylinder pocket with no flap, and vertical stitching dividing it into pen sleeves.  No code cylinders are present.
• There is a piece of nylon strapping sewn below the pen sleeve openings and is the same length as the top of the pocket.
• The bottom front corner of the pocket is cut off at a bevel on the side pointing in view direction, with the broader upside forming the border of the pen sleeves.
• The right sleeve has a cargo pocket below the cog emblem.
• The right arm pocket has a chevron flap.
• Two large chest pockets and two large front pockets with no zippers or flaps are present below the belt
• There are no leg pockets below the knees.
• There are two red stripes that run up the right side of the flight suit. The first begins at the bottom of the right leg and continues up to the right armpit. The second begins at the right wrist and stops at the bottom of the arm pocket. The stripe then continues above the arm pocket, behind the patch emblem to the shoulder seam.
• There are two black stripes that run up the left side of the flight suit. The first begins at the bottom of the left leg and continues up to the left armpit. The second begins at the left wrist and stops at the bottom of the compad pocket. The stripe then continues above the compad pocket up to the bottom edge of the pen sleeves then continues above the pen sleeves, behind the patch emblem to the shoulder seam.
• There are two black stripes that run up the left side of the flight suit. The first begins at the bottom of the left leg and continues up to the left armpit. The second begins at the left wrist and stops at the bottom of the compad pocket.  The stripe then continues above the compad pocket up to the bottom edge of the pen sleeves then continues above the pen sleeves, behind the patch emblem and up over the shoulder ending at the bottom of the collar.
• A piece of leather or leather-like material is sewn below the pen sleeve openings and is the same length as the top of the pocket. 

OPTIONAL Level two certification (if applicable):

• Patches are vinyl on textile with no edge border. If twill is used for the patch material the fabric texture will be vertically oriented. 
• Textured canvas is most accurate for the flightsuits construction as it is a thick materials with a "solid" structure .  A  "loose",  soft or  lightweight material is not accurate.

 

Compad

• Rectangular communications pad with patterned painted details matching reference photo.
• Compad is worn with the four large, rectangular buttons pointing towards the wearer’s elbow.  
• Compad is rectangular in shape and fits within the compad pocket window.
• Details of the compad differ from the standard TIE Pilot compad.
• Black buttons are smaller than the red and white buttons; the white button located adjacent to the button with multiple dimples may be a single piece, instead of split in two segments. 
• Compad base color is silver, metallic grey, or weathered silver. 
• Compad size is 2.5"  (63.5mm) x 2" (50mm). 
• Compad is fully visible above the glove, facing outward on the arm. 
• For basic approval (Level 1) a standard TIE pilot style compad painted and worn to match game references may be accepted for use.

OPTIONAL Level two certification (if applicable):

• Compad  shall be Inferno Squad style with correct button sizes, layout and colors.  Two black buttons at the top of the pad are smaller than the white and red buttons. The white button adjacent to the button with holes/dimples is not split. 
• Compad is moderately weathered / stained.

Gauntlet Gloves

• Black, leather or leather-like material, enclosed fingered, non-textured, (normal leather grain/texture/lines are acceptable) fitted gauntlet style.
• No buckles, straps, or decorative stitching.
• There is a split on the bottom gauntlet portion that runs from the glove opening to the wrist that is bridged with leather or leather-like material
• Gloves are made of leather. Is this supposed to be Level 2?

 

TACTICAL VEST

• The tactical vest is black Cordura nylon.
• All straps are black.
• There are a total of fourteen 1" (25mm) wide straps sewn to the tactical vest, with four laying horizonatally on either side of the pouches, and two at the front of each pouch.  Straps are sewn to match reference images.
• There are three M4 / M16 magazine pouches, with each filled by a rectangular package covered in the same fabric as the tactical vest.  The packages fill the pouches completely, and extend above the pouch. Each packages has a plastic strip mounted at top facing forward. Strip size is 5/32" x 1/2" to 2 5/8" (4mm x 12mm x 68mm).             
• There is a black canvas-covered block on the right side of the vest matching references, with a 1" ( 25mm )wide strip of elastic or webbing mounted to the vest, going across the front of the block.
• The main shoulder straps consist of ribbed leather or leather-like material. The front portion of the ribbed shoulder straps measure 1 3/8" (35mm).
• The front shoulder strap buckles are tri-glide buckles.
• Vest-front tri-glides are attached to the vest with 1 3/8" x 1 3/8" (35mm x 35mm) loops. The quick release buckles on the back of the vest are attached  by 1" (25 mm) loops. 
• There is a an approximately 1.5" x 1" (38mm x 25mm) specific buckle greeblie mounted above the tri-glide buckles on each side matching reference images.
• The shoulder straps cross near the top of the back armor box.  Each shoulder strap has a tri-glide that the end of each strap feeds into, near the back armor box shape.  See reference photos and the Costume Gallery for placement.
• There is a 1" (25mm) leather or leather-like waist strap present at the back of the tactical vest, and it is attached to the vest with one quick release buckle on the right  or left side of the vest at the wearers option.  This quick release buckle is hidden under the scout pouch, and is not seen when worn.  A single adjusting tri-glide is centered on the back waist strap.
• The Flyye tactical vest is not accurate and should be avoided.                        

OPTIONAL Level two certification (if applicable):

• The vest is fitted to the wearer.
• All vest shoulder and waist straps are made of black leather.
• Vest front tri-glides are specific to the games 3d model, and are attached to the vest with 1 3/8" x 1 3/8"(35mm x 35mm) leather loops.
• Game- specific 3d model buckle style greeblies are attached to the leather shoulder straps above the tri-glides. See reference images and the Costume Gallery for placement.
• Front shoulder straps which go over the shoulder and continue to the back are made of  3 layers of ribbed/ grooved leather strips which are glued/sewed/bonded together.  The first (bottom) layer is 1 3/8" (35mm) with the middle layer added to that. The middle layer shall be 1" (25mm) wide. The final layer is centered on top of the first two layers, and is 9/16" (15mm) wide.  The three bonded strips run the length of the forward portion of the shoulder strap assembly.
• The grooved part of the leather shoulder straps stop just past the wearers shoulders, and continues on as a single 1" (25mm) black leather strap, passing through tri-glides and into specific quick release buckles, which are held to the vest with 1" (25mm) black leather loops.  (see Reference Images and the Costume Gallery for placement and construction.           
• The quick-release buckles on the back of the vest, which hold the shoulder straps,  are attached  by 1" (25 mm) black leather loops.
• The back waist strap has a single quick release buckle mounted to the right side of the vest using 1" (25mm)  black leather loop. This buckle is hidden under the scout style pouch and is not seen when worn.

 

Shoulder Ammo Pouch

• There is an MP-40 ammo pouch attached to the left shoulder and must be filled.
• The pouch is black in color and made of canvas, or canvas-like material.
• Closure straps are made of black leather or leather-like material.
• There is a small pouch on the bottom of the pouch at the right side. 
• Pouch stitching is black. 

OPTIONAL Level two certification (if applicable):

• Attachment is not seen.  No straps are visible.  Magnets or other source of firm mounting is advised. 
• Oiler pouch is attached to the bottom right side of the right pouch.

 

Imperial Officer Under Belt

• The belt is constructed from leather or a leather-like material. A very slight texture is acceptable. 
• Approximately 2" (50.8mm) in width, up to 3" (76.2mm) is acceptable.
• There are no loops or extra holes on the belt.
• A single large snap or rivet is visible approximately 1" (25.4mm) from the left side of the buckle.
• The buckle is constructed from a horizontally brushed metal, or metal looking material.
• The buckle size is approximately 2 5/8" (66.7mm) high and 4 1/8" (104.5mm) wide with 0.5" (12.7mm)  radius rounded corners.
• Buckle is adorned with an Imperial Code Disk at the center.

OPTIONAL Level two certification (if applicable):

• Belt is made of non-textured leather.
• Two parallel grooves run the length of the belt  1/8" (3.1mm) in from edge. 
• Snap is worn to the left of the wearer 1" (25mm) from the buckle edge.
• Buckle has a slight horizontal curve.

 

Over Belt

•  The over-belt consists of 5 gloss black boxes made of ABS or similar plastic, mounted to a leather or leather like waist strap which closes under the thermal detonator. 
• The waist strap is approximately 1.5" (40mm) wide. 
• The over belt is worn around the under belt, so that the top third of the under belt shows above the ove-rbelt. 
• There are special-shaped boxes on left and right of the 3 central boxes which are horizontal in position as seen in reference photos.
• A total of 8 rivets are present with 2 rivets mounted vertically on the left and right at the edge of the special-shaped boxes.
• Hanging from the right side of the belt is a hip box made out of hard material. This is connected to the belt by  1.5" (40mm) wide black leather or leather-like straps. The strap is and as long as necessary to allow the box to hang on the wearers right hip.
• For basic L1 approval a standard Scout style hip box may be approved. 
• The strap is attached to the front of the over-belt through a slot on the right side of the central box. The back end of the strap goes behind the under-belt, to the left side of the thermal detonator. 
• The hip box strap has 1.5" (40mm) quick release buckles on the front and back.  Each buckle is attached at the mid point of the strap.

 

OPTIONAL Level two certification (if applicable):

• The  rigid front portion of the outer belt is made from the game's 3d model and scaled to the wearer.
• The box is smaller than a typical scout box, is curved, the back is closed with a back plate, and features a rectangular depression near the bottom out facing side of the box.               
• The boxes may be lightly stained or weathered.  Silver is not permitted.

 

Scout Style Pouches

• Two "scout" style pouches are made of black matte canvas or canvas-like material.
• The  "scout" style pouches are filled to appear full and worn at the back of the belt.
• The pouches will leave sufficient room for the Thermal Detonator mounted between them.
• Pouches may be hung from the tactical vest waist strap, or from the over-belt strap, at the wearers choice.
• Pouches are a maximum of 6 inches tall, 5 inches wide and 2 inches (152mm tall x 127mm wide and 50.8mm deep). The lower edge of the flap will not be wider than 2 1/2" (63.5mm).
• Pouches are proportional to the size of the wearer and match in-game references. 

OPTIONAL Level two certification (if applicable):

• Scout style pouches match in game references.
• Bottom edge of the pouch flap is less than half the overall width of the pouch.
• Pouch outer flap has a stitch set back 5/16" (8mm) from the edge.

 

Thermal Detonator

• Attached to the back of the belt is a rectangular gloss black  Thermal Detonator with a black corrugated hose.  The ends of the hose is covered by gloss black end caps.
• The Thermal detonator fits between the two back belt pouches.
• There are two silver detail greeblies on the central box. These details consist of a dome-shaped greeblie on the left side of the box and rectangular greeblie with  various designs on the right side of the box.
• For basic (Level 1) approval a gloss black Shadow Scout style Thermal Detonator with standard greeblies is acceptable, as long as the greeblies are painted silver.

OPTIONAL Level two certification (if applicable):

• Made from the game's 3d model and scaled to the wearer. 
• The detonator consists of a boxy central structure containing a ribbed hose, and end caps which are "closed" where the tube enters the end cap.
• The detonator box features a round dome-shaped greeblie approximately 5/8" (15.8mm) on the left side and a 3/4" x 1.5" (19mm x 32.7mm ) rectangular greeblie featuring various designs as seen in the reference images.
• The standard shadow scout thermal detonator is not accurate and is not to be used for Level 2 approval.

 

Holster

• Holster is made of black leather or leather-like material.
• A Stormtrooper style holster is acceptable for basic approval.
• Holster is worn on left side of belt.
• Holster is attached via 2 black leather straps which pass behind the belt, using two fasteners in the middle of the belt.
• Fasteners may be rivets, snaps, or Chicago screws.
• Note: The straps are slightly longer for this holster then seen on Stormtroopers.There is a retention strap which ends in a point approximately 1/2" (12.7mm) beyond a black snap closure. 

OPTIONAL Level two certification (if applicable):

• The holster is made of leather. 
• A leather square is seen under the rivet at the top corners of the holster where the straps are mounted. 
• Holster is worn empty.

 

Boots

• Calf high black leather or leather-like material.  Boots are dull in appearance. 
• Similar design to tall German jack boots or tall motorcycle riding boots are acceptable for basic approval.
• Boot has a round, plain toe. Harness style or box toe boots are not to be approved. 
• Ankle straps are to be removed. 
• Typical jackboots are not acceptable as they are too short.  The boot shaft must rise as close to the bottom of the knees as possible.  The boot shall be as tall as required to achieve this appearance.   See reference images. 
• Boots have an adjustment strap on the out facing side of the boot. 
• Adjustment strap has a square, silver adjustment buckle.
• Heels are made of rubber or similar material and may have tread or no tread.
• Boots may contain zipper closure but must be concealed with boot material as to not be visible.

 OPTIONAL Level two certification (if applicable):

• Boots stops just below wearers knees.  Shaft height should be 15" (38cm) or as required to stop just below the wearers knees.  
• Boots have a flap with adjustment strap with square silver buckle that starts at the middle back of the boot and wraps around to the outfacing sides.  See reference images for shape of the adjustment flap and strap.
• Boots are not shiny, they have a matte appearance.

 

Face

• Hair is medium length with a part on the side swooped to the right and brown in color.
• Face is clean shaven. Sideburns do not extend past bottom of ear canal.

 

Chest Box

• The chest box is required to have the same configurations as seen in the photo.
• The chest box is held to the armor with an invisible system which is not visible when the box is removed.  Strong magnets are advised. 
• The chest box is painted glossy black and matches the sheen of the armor. 
• The chest box has five detail pieces: 1 Red, 1 White, 1 black, 2 Blue. 
• There is a 1/8" (3.1mm) thick white pinstripe border around the square detail pieces.
• There are two round indicator lights above the rocker switches, one white, one red respectively.
• There are three rocker switches below the round indicator lights. The rockers are always gray, white, gray.   The gray rockers have red dots or indicator lamps in the bottom outfacing portion.
• There is a 1/8" (3.1mm) thick white pinstripe that runs horizontally across the bottom portion of the box.
• There is a male silver snap or radio jack and a silver round disc with cone knob greeblie on the lower portion of the box below the horizontal pinstripe.
• There are two "gear" type greeblies affixed to either end of the lower tube portion of the box, and are painted silver or metallic grey. 
• There are two machined aluminum or molded silver greeblies in the hose ports of the box. See reference images and the CRL Gallery view. 
• The hose port greeblies feature 8 round depressions around a raised disc.  The color matches the gear type greeblies. 
• Chestbox may be light to moderately weathered or stained.  Silver is not permitted. 
• The red and white indicator lights and rocker lamps may be functional.

OPTIONAL Level two certification (if applicable):

• Box is electrically lit to include the red and white squares, both rocker lamp lights and the red and white indicator lights on top of the box. 
• Box is based on the games 3d model and is scaled to the wearer and consistent with armor size.

 

Hoses

• Hoses are ribbed rubber 1.25" (31.75mm) in diameter.
• There are two plastic (polypropylene, pond hose etc.) or rubber gas mask hoses that run from the helmet ports to the chest box ports. 
• Hose length should be proportional to the wearer. 

 

BlasTech E-11

• Based on a real or replica Sterling sub-machine gun, scratch-built, or a modified commercial toy Stormtrooper blaster.

OPTIONAL Level two certification (if applicable):

• Folding stock (does not need to function).
• No ammo counter is present.
• D-ring mounted on the rear.
• Correct style scope.
• No power cylinders on the magazine housing.
• Scratch-built, resin cast, Hyperfirm rubber cast blasters have a total of (7) U shaped channels on blaster (all holes on barrel are covered).
• If using the popular commercially available Stormtrooper blasters, you shall grind off the T-tracks and replace them with U shaped channels and cover the open rows of holes (total of 7 U shaped channels in all).
• Correct greeblies on the left rear area are present (door catch and two "hammers").

 

DLT-19x

A DLT-19x is an MG-34 with T-tracks on the barrel, a scope mounted on top of mag loader, red ring around the scope, ejection port cover added, and a small disk on the left side, on a real or cast replica of a MG-34 machine gun.

• The DLT-19x rifle is scratch-built or is a high-end prop replica which matches reference images.

OPTIONAL Level two certification (if applicable):

• Accurate MG-34 replica base using correct size and proportions,  either cast or 3d printed from an original MG-34.                                                                                                        
• The scope has a design specific to the game's 3D model, and has a red ring which matches reference images for placement and size.                                                                       
• Scope should include real glass lenses.    

 

Thermal Detonator

• Detonator is a handheld sphere that is chrome silver in color.
• The Detonator is worn on the right front of the Over Belt, and is worn to the right of the Detonite Charge if that is worn.
• Asymmetric latitudinal lines are etched into the reflective silver body of the detonator.
• Detonator appears to be open like a puzzle, creating a trench around the circumference of the sphere.
• Three front activation indicators are visible within center band.
• A light grey ovular and contoured top thumb switch is seen with a raised grip surface.
• Detonator has the appearance of an inset red arming indicator, functional or non-functional on top in front of the thumb switch.

OPTIONAL Level two certification (if applicable):

• Thumb switch activates the detonator.
• Switch slides back to reveal a lit red arming light.
• The three front activation indicators light up and flash based on visual references.
• The official Star Wars LFL licensed Thermal Detonator sold as the "hot potato" game should be allowed for Level 2 because it meets the criteria listed above.

 

Detonite Charge 

• The Detonite charge is grey , olive olive -grey or olive drab in color and hangs from the scout belt with a fastener that is not seen.  
• The Detonite Charge  is worn on the right front of the Over Belt, and is worn to the left of the Thermal Detonator  if that is worn.
• The Detonite Charge is a cylindrical explosive which has a flanged base extending outwards from the bottom of the cylinder. The base  stops 1/4 of the way up the cylinder. 
• Mounted onto the cylindrical part of the charge are two square "vent" greeblies  which feature mounting tabs held on with four domed-head wood screws. 
• The top of the charge is depressed 3/8" (9.5mm) and features various greeblies mounted around a central core which rises above the top rim of the cylinder.  Inside the depressed area are several rectangular greeblies as well as two silver raised knurled thumbscrews. 
• The "core" has a silver raised cylindrical "pipe" fitting with a groove running all the way around it.   
• The flange around the base has a total of 36 depressions or holes in groups of 9 spaced equally around the diameter. Hole diameter will not exceed 1/8" (3.1mm).
• The open area of the flanged base features various designs and greeblies which match screen references.
• The charge may be scratch built, cast, printed or high end prop replica. 
• There is a 1" (25mm) red or brown-red ring which runs around the charge where the flange meets the cylinder.  There are two yellow or ochre-colored rectangular stripes which divide the red ring into two segments.  These yellow stripes are situated between the middle of the cylinder height, and stop 1/4" (6.35mm) above the bottom of the flange.  There may be two different designs in the yellow stripes which match screen images. 

OPTIONAL Level two certification (if applicable):

• Detonite charge is made from the games 3d model and matches game references including color and markings. 
• The detonite charge is electrically lit and feature sound effects when 'activated'.
• The black markings on the yellow stripes match the markings seen in game.

well done! ????

[Blackwatch[CMD-DCA]]

Thank you so much for fixing this !~ i tried and tried and tried on two different computers. 

The leather gloves was intended to be L1 because in the l1 text it says leather or leather like.   Could you go ahead and update so that the formattting remains? 

The only spot I see that would require some formatting is the DLT19 X, the spacing is off as well as color needs to be changed for L2. 

 

thanks again!!!!!

[MahXPrime[501st]]

It looks great, good job on this final touch ! Happy to see all the work ends up into this clean & sharp conclusion, really, it feels nice, proud to see that !

[RAIDER[COTG]]

@Blackwatch @TX-20113 @MahXPrime

Are we set then here?  No further edits required?

This means we just need new pictures to publish yes?

[TX-20113[501st]]

2 minutes ago, Raider said:

@Blackwatch @TX-20113 @MahXPrime

Are we set then here?  No further edits required?

This means we just need new pictures to publish yes?

Yes ? 

[MahXPrime[501st]]

And double Yes !

[Blackwatch[CMD-DCA]]

Yes! Yes yess! Yesss Yesss Yess!!

[TX-20113[501st]]

On 7/4/2020 at 9:24 AM, TX-20113 said:

TACTICAL VEST

Ahm... i may brinh some trouble in, but for some reason i was reading again the tactical vest's part of the new CRL and, where is that leather loop/strap which is attached above that weird greebly on the front shoulder straps? 

I read it 3 times and it is not in the text ? 

 

Greetings 

[Blackwatch[CMD-DCA]]

you are right, i missed it. 

To me this thing looks more like a piece sewed onto the front, than a loop.  

Proposal for L1:  A leather or textile loop is located approximately 2" (50mm) above the specific tri glide greeblie on the front of each shoulder strap. 

Proposal for L2 A leather  strip as wide as the strap, and 7/8" {22.2mm) tall is located approximately 2" (50mm) above the specific tri glide greeblie on the front of each shoulder strap. The leather strip is sewn at the ends, firmly mounting it to the strap.

 

proposed edit for L1

The front shoulder strap buckles are tri-glide buckles.

Vest-front tri-glides are attached to the vest with 1 3/8" x 1 3/8" (35mm x 35mm) loops. The quick release buckles on the back of the vest are attached  by 1" (25 mm) loops. 

There is a an approximately 1.5" x 1" (38mm x 25mm) specific buckle greeblie mounted above the tri-glide buckles on each side matching reference images.

The front shoulder strap buckles are tri-glide buckles.

A leather or textile loop is located approximately 2" (50mm) above the specific tri glide greeblie on the front of each shoulder strap. 

The shoulder straps cross near the top of the back armor box.  Each shoulder strap has a tri-glide that the end of each strap feeds into, near the back

Proposal edit for L2 

• Front shoulder straps which go over the shoulder and continue to the back are made of  3 layers of ribbed/ grooved leather strips which are glued/sewed/bonded together.  The first (bottom) layer is 1 3/8" (35mm) with the middle layer added to that. The middle layer shall be 1" (25mm) wide. The final layer is centered on top of the first two layers, and is 9/16" (15mm) wide.  The three bonded strips run the length of the forward portion of the shoulder strap assembly.
• A leather  strip as wide as the strap, and 7/8" {22.2mm) tall is located approximately 2" (50mm) above the specific tri glide greeblie on the front of each shoulder strap. The leather strip is sewn at the ends, firmly mounting it to the strap.
• The grooved part of the leather shoulder straps stop just past the wearers shoulders, and continues on as a single 1" (25mm) black leather strap, passing through tri-glides and into specific quick release buckles, which are held to the vest with 1" (25mm) black leather loops.  (see Reference Images and the Costume Gallery for placement and constructio