tat2trooper anovos shadow trooper build

[Dropkick[CMD-XO]]

I love them skull helmets.

Something to think about when I get my shadow trooper cleared.

[Tat2trooper[501st]]

10 hours ago, Dropkick said:

I love them skull helmets.

Something to think about when I get my shadow trooper cleared.

Yea they are great quality I did a review on FISD. Might repost here also.

[nanotek[CMD-DWM]]

On 4/4/2021 at 1:33 PM, Tat2trooper said:

Did 3 to 4 lightly brushed coats on the stencil. After last coat was maybe 4 hours then I slowly pulled stencil off came out perfect.

So beautiful! I would be too scared to wear this in fear of weathering it! 

[Tat2trooper[501st]]

Pouches performed well in a fitting on my belt. Felt sturdy and not too loose.

[Tat2trooper[501st]]

Also going to try and knock these forearms out tomorrow if I have time.

 

[Tat2trooper[501st]]

[Tat2trooper[501st]]

Just noticed I need to trim these hand guards down some they look a little too thick.

[Tat2trooper[501st]]

Primer coat on the tube and TD clips. Then gloss back once done.

Belt plate reinforcement

[Tat2trooper[501st]]

Marked the belt for my holes.

[Tat2trooper[501st]]

Ab details done

I did the sharpie around the edges to get rid of the grey color.

Forearm cover strips 

[IcyTrooper[CMD-DL]]

[Tat2trooper[501st]]

 

[Tat2trooper[501st]]

 

[IcyTrooper[CMD-DL]]

4 hours ago, Tat2trooper said:

 

Getting there! Just FYI if you are going to do Specialist (L2) the edge of those clips will need to be touching/closer to the end caps.

[Tat2trooper[501st]]

On 4/18/2021 at 2:01 PM, IcyTrooper said:

Getting there! Just FYI if you are going to do Specialist (L2) the edge of those clips will need to be touching/closer to the end caps.

Yeah I need to scoot them over a tad bit.

[Tat2trooper[501st]]

Got this shin and thigh ready for fitting. Also added reinforcement pieces to inside forearm.

[Dropkick[CMD-XO]]

Keep up the good work. ?

[Tat2trooper[501st]]

3 hours ago, Dropkick said:

Keep up the good work. ?

Thanks brotha.

[Tat2trooper[501st]]

I noticed I used the trooper bay hand guards instead of the anovos ones that came with the kit. So I trimmed them up and got them ready.

[Tat2trooper[501st]]

right thigh came out perfect for fitting after first trim left one needs a little more trimming and fitting

second forearm almost complete

[Tat2trooper[501st]]

[IcyTrooper[CMD-DL]]

I'd say that's a good fit!

[Tat2trooper[501st]]

Need quick help guys which ones are for thigh?

[Tat2trooper[501st]]

[IcyTrooper[CMD-DL]]

13 hours ago, Tat2trooper said:

Need quick help guys which ones are for thigh?

36 should be for the front and 37 should be for the back with Anovos.

To verify that they are numbered correctly here are the dimensions:

• #36 - 18" x .79" x .06" (46cm x 2cm x 1.5mm)
• #37 - 13.4" x .79" x .06" (34 cm x 2cm x 1.5mm)