swman77's Death Trooper WIP

[swman77]

This week was pretty eventful. I dove headfirst into the world of 3D printing for the first time, got a printer, set it all up. It was very exciting. After a few test prints I started in on the armor, which is printing now. I have a local trooper who is showing me the ropes. I know I’m still a long way off but right now I’m very excited. 

I also went to a troop for the first time today, where I served as a handler. It was so much fun and as always all the troopers there were so welcoming. I’m so looking forward to joining your ranks! 

 

[MKE-Trooper[TX]]

16 hours ago, swman77 said:

This week was pretty eventful. I dove headfirst into the world of 3D printing for the first time, got a printer, set it all up. It was very exciting. After a few test prints I started in on the armor, which is printing now. I have a local trooper who is showing me the ropes. I know I’m still a long way off but right now I’m very excited. 

I also went to a troop for the first time today, where I served as a handler. It was so much fun and as always all the troopers there were so welcoming. I’m so looking forward to joining your ranks! 

 

Thanks for sharing @swman77  I never thought to start getting involved and serving as a handler while finish up my kit and getting approved. Great opportunity to meet the local group and learn. 

[swman77]

Update: My Jim Tripon undersuit came today. The material is pretty incredible, and it fits well, though I do have some trouble lifting my arms up. I tried it on with my boots and am happy with how it’s looking so far. 

I’m also in the midst of printing my armor pieces. I’ve done quite a few already, but still have a bunch of the big pieces left. I’m going over to a trooper’s house tomorrow to learn about sanding/post processing. 

 

[Chaos[CMD-DCA]]

Jim's suit is awesome. I wouldn't worry about lifting your arms too much. Wait till you get the upper armor on. 😁

[swman77]

Yeah that’s what I figured 😂

[swman77]

Ok so I am nearing the end of printing, and have spent the past month sanding, priming, painting, gluing, etc. 

 

A couple things I am confused about are the panel behind the "ladder detailing" in the forearms how the cylinders attach to the forearm.

 

1. For anybody that has MCM (Tom Campbell) files, once the forearms are printed, there is no backing to the ladder detailing as shown in the photo below, the holes are just open. Is there a file I'm missing? If not, how do you recommend I make my own?

 

 

2. Also, I don't see any piece to connect the three cylinders to the forearm. Again, am I missing it or do you all do it a different way? 

 

 

[Chaos[CMD-DCA]]

I've never heard that MCM Design's files (Previously known as Tom's files) have the ladder recesses open. That's weird, I guess you could print a 2-3mm thick rectangle piece and glue it behind the ladder. As far as the arm cylinders, most just glue them to the arm or put screws thru the inside of the forearm into the cylinders. I have seen a mounting bracket in some ones 3D files but I don't know if Tom's has it. I sent him a message to inquire about your questions. When I hear back from him I will update my post.

[swman77]

Oh thanks @Chaos, that’s awesome! Good to know what others do. I’m interested to hear what he says. 

[Salwii[TX]]

On 4/27/2024 at 6:14 AM, swman77 said:

Update: My boots from KeepTrooping arrived today. I was shocked, since I only ordered them on April 12th and I was prepared to wait much longer to receive them.

They look pretty awesome. The only thing is that the laces are pretty short. Has anybody else switched them out for longer ones? I checked the CRL and I can't see why not, since they are hidden beneath the flap. 

 

got the full Undersuit Kit from Imperial Boots.

 

Yes the laces are a bit short. i just replaced them with some longer no hussle. My Advice: Cover the lower Edge from you shins. mine ripped the Bootcover while Walking. it looks worn but a but too much 🙈.

[Chaos[CMD-DCA]]

On 6/24/2024 at 6:03 AM, swman77 said:

Oh thanks @Chaos, that’s awesome! Good to know what others do. I’m interested to hear what he says. 

Jed, talked with Tom, he said he has nothing to do with MCM Design or the files that they are selling now. He said he could help. With that being said, if you have already printed the forearms, just print a 2-4mm thick backing strip and glue it on, or add the strip into the 3D file before you print them. 

[swman77]

Oh I thought those two were one and the same, I apologize for mixing that up. 
 

Thanks for the info, I guess I will just print a backing on my own then.