Deamos's ISB Tactical Agent WIP

[Deamos]

Hat: TBC - but Jim Tripon more than likely

Chest Armor: TBC

Back Armor: TBC

Shoulder Bells: Mr Pauls Shoretrooper - Galactic Armoury

Biceps: Mr Pauls Shoretrooper - Galactic Armoury

Gauntlets: Galactic Armoury

Shins: TBC

Boot Armor: Darthberry 3d Files - Though may swap to Galactic armoury at later date

White Belt: 2" White Leather with grooves along top and bottom

White Belt Buckle: Taken off my Imp Black Belt (Unknown source)

White Belt Boxes: Philoprops Andor Style

Black Tactical Belt: 2" wide 3mm thick Ribbed Rubber

Belt Boxes: Designed custom boxes approximately H77mm x W40mm x T30mm and a single larger box - Split in two to allow black surrounds on facets

Belt Rear Box: Darthberry 3d Files

Tunic & Pants: TBC - but Jim Tripon more than likely

Boots: German Jack Boots

Gloves: Keep Trooping [Shoretrooper]

Chest Radio: CGSProps (Etsy)

 

Edited Monday at 10:18 AM by Deamos
Updating what's "completed"

[Deamos]

Adding the main weapon on to my build list.

Base weapon: Airsoft MP40

Stock: AR15/M4 PDW Stock - with a castle style nut towards the gun screw end

Stock to Weapon joiner  TBC but probably custom or airsoft adaptor of some type

End Barrel: E11 style with custom end tip and Blitzkrieg PTR Spike Front Sight

 

Rest is still being worked on 🙂

 

[Deamos]

Stating with the easier bits - calling the white leather belt done.

[Deamos]

Worked on the gun a little from what I can work out so far and until an airsoft MP40 turns up in the post.

Designed an adaptor for the rear of the weapon to allow the PDW stock to screw into it to create the extended stock.

Noticed the front barrel nut was moved from the base of the barrel to be used at the barrel tip, so took the E11 barrel shroud and cut it down slightly based on one of the officer gripping that part nearly fully to give an indication of a short length.

Then added the barrel nut to the end of it.

Also added in one of the barrel shroud holes as bung to allow the sight to be printed separately and attached/detached as needed.

Hopefully once the airsoft weapon turns up I'll check again for fit.

 

Now to just work on finding the damn dual scope attachments parts....grrrrrrr

[Deamos]

Stunt version of the weapons coming together nicely - got it confirmed from one of the prop guys it was based on the MP40 as suspected.

Still on the hunt for the damn dual scope mount though.

[Deamos]

Got one half of the leg straps sorted as well.

For the reference pictures looks two of the larger Shoretrooper straps on each calf.

The lower strap has a visible white buckle hidden behind the normal trooper buckle and then webbing attached to allow for quick suiting up.

The upper strap doesn't seem to be done in the same way so this could be more webbing hidden behind the strap and then Velcro used to secure it behind the shin plate. Still testing this one when I get more straps from Mr Paul Shoretrooper.

[Diet_Evil]

In regard to the blaster looks like they also moved the original barrel down flipped the front site post and used it as a brace to the shroud.

Im not sure how much faith we want to put in the black series figures blaster but it doesn't look like a standard sterling or e-11 shroud. A clear set pic of this would be a god send.

Are you using files or real world on the stock? I have files off my E-11D that just need the larger shoulder pad.

[Deamos]

17 hours ago, Diet_Evil said:

In regard to the blaster looks like they also moved the original barrel down flipped the front site post and used it as a brace to the shroud.

Im not sure how much faith we want to put in the black series figures blaster but it doesn't look like a standard sterling or e-11 shroud. A clear set pic of this would be a god send.

Are you using files or real world on the stock? I have files off my E-11D that just need the larger shoulder pad.

Good shout on the barrel flip - i'll give it a try to see if i can get it to work.

On the stock I've goner real world using a CYMA PDW Stock for M4/AR-15 AEG with a printed adaptor on the back of the MP40 to screw it in to. Once my all metal airsoft turns up I'll try it on that too. One stunt and one hero is what I'm going for.

I've asked the prop maker on Insta if they have any info on the scope mount as that's what's baffling me at the moment.

[Deamos]

Just taking a look at this wide shot of K2 holding the blaster it looks a hell of a lot longer than the close up shot.

The red part is the magazine slot and then there is some barrel up to what I think was the nut before the e11 shroud starts. It does look a lot longer and thus probably a normal e11 shroud length.

So i'll try work out how to get the bit at the bottom mounted to it all.

This angle from the hospital show it more full length as well starting just after the webbing toggle:

 

 

For the scopes this is a better angle to show how they look really offset from the main body of the weapon - at least in this characters loadout.

 

[Tarrif[TX]]

On 6/2/2025 at 6:27 AM, Deamos said:

Got one half of the leg straps sorted as well.

For the reference pictures looks two of the larger Shoretrooper straps on each calf.

The lower strap has a visible white buckle hidden behind the normal trooper buckle and then webbing attached to allow for quick suiting up.

The upper strap doesn't seem to be done in the same way so this could be more webbing hidden behind the strap and then Velcro used to secure it behind the shin plate. Still testing this one when I get more straps from Mr Paul Shoretrooper.

Very good catch on that. I hadn't noticed. Might even be one on the top strap too. The bottom strap is pulled very tight!

[Blackwatch[CMD-DCA]]

very very interesting, from struggling with my own I can see why wardrobe would want to put a regular white quick side release buckle on there. only weirdos like us would dare look at a boot! 

[Deamos]

11 hours ago, Blackwatch said:

very very interesting, from struggling with my own I can see why wardrobe would want to put a regular white quick side release buckle on there. only weirdos like us would dare look at a boot! 

Totally - from that shot alone it's also very hard to spot if they did the same to the top strap. But it does look like they did it too.

They only need to walk for like a few meters but guess even take after take you need to be able to have them functional more these days 😉

[Deamos]

Think I bought a bit too much rubber.... Got enough to test out creating 80 odd belts!!!!

 

[pyro[TX]]

Can you send me a link to that please? 

[Tarrif[TX]]

1 hour ago, pyro said:

Can you send me a link to that please? 

I got some  great material from Amazon. (Link: https://a.co/d/adajFKJ)

On 5/29/2025 at 3:14 AM, Deamos said:

Worked on the gun a little from what I can work out so far and until an airsoft MP40 turns up in the post.

Designed an adaptor for the rear of the weapon to allow the PDW stock to screw into it to create the extended stock.

Noticed the front barrel nut was moved from the base of the barrel to be used at the barrel tip, so took the E11 barrel shroud and cut it down slightly based on one of the officer gripping that part nearly fully to give an indication of a short length.

Then added the barrel nut to the end of it.

Also added in one of the barrel shroud holes as bung to allow the sight to be printed separately and attached/detached as needed.

Hopefully once the airsoft weapon turns up I'll check again for fit.

 

Now to just work on finding the damn dual scope attachments parts....grrrrrrr

The rear portion of the ISB blaster is from the E-10D the Mudtrooper uses. Same stock, etc.

[Deamos]

2 hours ago, Tarrif said:

I got some  great material from Amazon. (Link: https://a.co/d/adajFKJ)

The rear portion of the ISB blaster is from the E-10D the Mudtrooper uses. Same stock, etc.

Yeah the Stock is a Cyma 416/AR15/M4 PDW Stock - there are similar ones but this looks the same as the mud one but also in the reference pics there is a distinct castle nut at the join to the main gun body. This one has that feature 🙂

[Deamos]

Rubber belts done and fits and hangs really nicely.

 

[Blackwatch[CMD-DCA]]

Joe if you got a roll of that would you be willing to sell slabs of it to help a brother out (and recoup some of your cost)

TBH it looks just like what I used on my BSG knuckledragger costume for the vest. 

[Deamos]

2 hours ago, Blackwatch said:

Joe if you got a roll of that would you be willing to sell slabs of it to help a brother out (and recoup some of your cost)

TBH it looks just like what I used on my BSG knuckledragger costume for the vest. 

More than happy to slice this large slab up, but bring over the pond it probably will cost more to get it to you than it’s worth 😢

[Blackwatch[CMD-DCA]]

oh, thats true!! i never thought about that. I know I can get a roll of it. Ill check with my local rubber house, they have a ton of stuff. 

[Deamos]

26 minutes ago, Blackwatch said:

oh, thats true!! i never thought about that. I know I can get a roll of it. Ill check with my local rubber house, they have a ton of stuff. 

No worries - this first one was a little rough around the edges but I've now got a 2" wide section of aluminium bar to act as a cutting guide. Works perfectly.

[Blackwatch[CMD-DCA]]

i bought a very heavy aluminum construction yardstick that is 2" wide for that very reason. Great for cutting leather belts once I clamp it down. 

[pyro[TX]]

Dont know it this would work but you could try this, its a leathercutting tool to make belts.
https://www.amazon.com/BESTNULE-Leather-Cutter-Cutting-Adjustable/dp/B0BRH94KDT/ref=sr_1_3?crid=275ZUW6GM9YCM&dib=eyJ2IjoiMSJ9.9F-9EIpsmR83NYnLOVjyqfLoW58oC97UcTarMaOARDB3n3X--vlwt0QtSeaWM8gFT4coNhQDf2RLW_i0ytgQHNidsoDd0d3nLpcC6aUsclRucklcTapshFMWtt5pUewYMag_pYeKFsedAMU-_qxDUKvWFrzWGu2tfKBQW0890V0KXTsaGvYc8w_AUsuerH6_m2vid9o2c6EUpgoMJs3uKzwZsw5xcjwkg8ximO-sFKRhykw9u1onIGQGf0S8ZUrNlOrQlDjWE_8fCP1Bf003c3Hl89ffPDqZafjVA8Thk2o.cO5JPGvmKWXHEv5CKGLDb_C7KMdvv73_NROSfIelbsI&dib_tag=se&keywords=leather+belt+cutting+tool&qid=1749493481&sprefix=leather+belt+c%2Caps%2C164&sr=8-3

[Deamos]

17 hours ago, pyro said:

Dont know it this would work but you could try this, its a leathercutting tool to make belts.
https://www.amazon.com/BESTNULE-Leather-Cutter-Cutting-Adjustable/dp/B0BRH94KDT/ref=sr_1_3?crid=275ZUW6GM9YCM&dib=eyJ2IjoiMSJ9.9F-9EIpsmR83NYnLOVjyqfLoW58oC97UcTarMaOARDB3n3X--vlwt0QtSeaWM8gFT4coNhQDf2RLW_i0ytgQHNidsoDd0d3nLpcC6aUsclRucklcTapshFMWtt5pUewYMag_pYeKFsedAMU-_qxDUKvWFrzWGu2tfKBQW0890V0KXTsaGvYc8w_AUsuerH6_m2vid9o2c6EUpgoMJs3uKzwZsw5xcjwkg8ximO-sFKRhykw9u1onIGQGf0S8ZUrNlOrQlDjWE_8fCP1Bf003c3Hl89ffPDqZafjVA8Thk2o.cO5JPGvmKWXHEv5CKGLDb_C7KMdvv73_NROSfIelbsI&dib_tag=se&keywords=leather+belt+cutting+tool&qid=1749493481&sprefix=leather+belt+c%2Caps%2C164&sr=8-3

I've got one of these for any leather work I do but the rubber was a bit "sticker" to pull it through and to keep the edge smooth and clean. I ended up using a fabric cutting wheel as that made a great groove and running it over it several passes went through in the end but needed the ally bar to act as a guide.