ISB Tactical Agent- Finalized CRL text.

[Blackwatch[CMD-DCA]]

----------FINALIZED TEXT GOES BELOW THIS LINE (THIS IS THE OFFICIAL TEXT FOR THE CRL DEVELOPMENT)------------

Description: Imperial Security Bureau Tactical Agent
Prefix: TX
Detachment: Spec Ops Detachment
Context: Star Wars: Andor (TV Series)

Costume description here

Special Notes:

The armor parts are gloss white, or as specified in each part description, and made from one of these (or similar) types of materials:
Fiberglass
ABS (Acrylonitrile Butadiene Styrene)
HIPS (High Impact Polystyrene)
PLA, ABS, PETG (3D Printing)
Polyurethane Rubber
3D Printed parts are permitted but all print lines and other artifacts must be removed.
Blasters are not required for legion membership per our weapons policy.

TEXT

 

Hat

• Fabric matches the tunic and pants.
• Base of the hat is conical, with a crown about 4" (101.6mm) tall.
• Front and rear “flaps” overlap on the sides and are about 4" (101.6mm) high.
• Front bill extends 3" (76.2mm) down, decorated with (5), (6), (7) or (8) concentric stitches.
• An Imperial Code Disk is positioned in the center of the front vertical “flap”.

OPTIONAL Level two certification (if applicable):

• Disks do not feature a notch or groove details.

Tunic

• A long-sleeved, black jacket that falls just to mid-thigh, with no visible zippers or buttons. 
• Fabric is a plain weave cotton similar to duck canvas.
• Has a high mandarin style collar with a left-over-right closure that rises from the front of the tunic.
• The front closure overlaps left over right and rises from the hem at the bottom of the tunic to the top of the collar. 
• Four rectangular pockets are present on the jacket front, covered by large flapped closures. Lower pockets are larger than the ones on the upper chest. Lower pocket seams rest on the same seam as the end of the tunic
• The rear of the jacket has a horizontal seam present near the upper back. Two vertical seams start below the horizontal upper back seam moving down the bottom of the jacket. 
• Two black tunic hooks to hold the belt in place are permitted. If used, the hooks will pass from the inside of the tunic to the outside through holes on either side of the tunic at the hip. The belt covers the holes.
• One pocket is present on each arm of the jacket, each covered by large flapped closures.
• The top of the arm pocket flaps are in line with the top edge of the chest pockets. 
• Cuffs on the sleeves are about mid-distance to the elbow. The material folds back on itself to form the cuff.

OPTIONAL Level two certification (if applicable):

• The front jacket flap will have rectangular stitch marks with a stitched X inside where Velcro is attached to keep the flap closed.
• Fabric has the appearance of waxed canvas or oilskin fabric. 
• If left arm rank bars are present, the black fabric should be similar to duvetyn type of fabric and will have 3 equidistant horizontal stitch lines through each rank bar.

Chest Armor 

• Chest armor matches visual references being accurate in shape and design. 
• Chest armor is painted gloss white to match visual references. 
• Light to moderate weathering consistent with reference images is permitted.
• The join between the chest and back armor are created by an angled sweep starting at the bottom of the chest armor and finishing at the bottom of the back armor. This may be held closed with magnets, Velcro, or another hidden fastener. 
• There is an indented area around the outer edge of the center flat section.
• Buckles attach to upper chest plate and are painted gunmetal or dark silver. 
• Shoulder straps are affixed to the chest plate at the buckle. The shoulder strap is white. It is permitted to be made of cast flexible urethane or other flexible material.
• To the lower left side of the center flat panel is a recessed area angled inward from bottom to top with a raised rectangle greeblie and a recessed horizontal elongated oval. 
• Left of the recessed area is a raised square that extends from the center to the curved side of the armor.
• On the top left side of the raised area is a raised oblong detail that protrudes outwards.
• Chest shall be painted to match helmet and back armor.

OPTIONAL Level two certification (if applicable):

• Buckles have black recess on upper narrow section and the lower recess shall expose the chest armor.
• Moderate weathering consistent with reference images is required.

Back armor

• Back plate is painted to match the chest armor, shin and arm armor. 
• Back plate has a collar that extends upwards and tapers to the chest plate.
• Chest and back plate meet at the sides.
• There are 2 hose connectors located at the top of the back plate approximately centered above each rectangular cut out/greeblie. 
• Back has two large cut out recesses with vent details and greeblies inside, all painted the same white as the armor.
• The vents at the top of the boxes may have the openings darkened with weathering.
• Four raised bars approximately .375" (10mm) long aligned to the top of the recessed box opening may be present.
• Each recess has different and specific set of boxes inside that are painted to match the recessed box color. Light weathering is preferred inside of the recesses.
• Bottom left features a smaller rectangle cut out with the left side stepped.
• Half circle indent detail beneath the backpack section must be present.
• There is a long thin raised greeblie positioned central and below the 2 large recesses.
• There is a small raised circle greeblie positioned central and below the above named greeblie.
• There is a raised slot on each shoulder for the straps to fit into.
• Shoulder straps are white and are affixed to the chest plate at the buckle.

OPTIONAL Level two certification (if applicable):

The hose fittings are angled forward.
There is a raised step on the bottom of the main back box.
There is a recessed hole approximately .31" (7.8mm) above the top left corner of the left recessed box.
There are two indented squares approximately 1⁄4" x 1⁄4" (5mm x 5mm) aligned vertically above the right upper corner of the left recessed box.
 

Shoulder Armor

The shoulders are considered effectively symmetrical; they may be worn interchangeably on the left and right shoulders. Velcro is permitted to keep the shoulder armor in place. 
Shoulder armor is held up with a strap mounted under the shoulder bridge.

OPTIONAL Level two certification (if applicable):

There is no elastic strap that wraps around the inside of the bicep.

Bicep Armor 

Biceps are a split design, joined in the front. A gap may be present at the back.
There is a left and a right side. They are not interchangeable.  
Bicep cover strips are raised and beveled with an added strip layer on top.
Biceps may be held to the shoulder armor with black elastic. 
Biceps are painted to match the armor. 

Forearm Armor

Hand Plates

Gloves

Upper Belt

Lower Belt

Hip Plates

Trousers

Shin armor

Boots

Optional parts 

Tac Vest

Radio 

Blaster

Goggles