Carlos's Shadow Scout WIP

[Force Crush[TX]]

Will this work?

[retrofire[501st]]

Will this work?

j

 

Yep that's the stuff I used for my lid. Be sure to scuff up both sides of the locations you are gluing with some sandpaper or fine scotchbrite and clean them with isopropyl alcohol before bonding and give the epoxy and hardener a good mix before applying. Keep in mind once you use this it's permanent so the measure twice cut once rule applies😉

[Force Crush[TX]]

Thanks for the advice!

[retrofire[501st]]

Thanks for the advice!

 

Anytime my friend! Look forward to seeing your build progress.

[Force Crush[TX]]

I have a question about what weapons can a Shadow Scout use. I know that the blaster is the default weapon of choice but, what other weapons can I use once I finish my costume?

[Darth Emphatic[CMD-DWM]]

Hi Carlos, all the approved weapons are in the CRL. You can do the hold out blaster, E-11, or DLT-19.

[retrofire[501st]]

You're a Scout brother do not carry the E11 that's a Stormies territory. Snag yourself a DLT😀

 

 

Sent from my iPad using Tapatalk

[Sall]

I have all three Carlos, just because i can swop about depending where im trooping the Dlt it huge on me and dont want to knock any kids heads off if the trooping area is a bit confined ...and because im not used to it yet lol

[Force Crush[TX]]

Do you know someone who sells those blasters at a decent price?

[Force Crush[TX]]

The BBB IS here!

[retrofire[501st]]

Ohhhhh it's on now!!!ðŸ‘ðŸ»

[Force Crush[TX]]

Ohhhh yes!

Thing is I don't know where to start. I don't own a dremel to cut the visor. Maybe I'll start with the little details.

[Force Crush[TX]]

O also have my blaster!

[BananoPower22[501st]]

Nice to see you've got a thread already set up here! Let's get this done and suit you up brother!

[Darth Emphatic[CMD-DWM]]

Step 1 - buy a Dremel . It's one of the most universally useful tools I've ever owned. I use it for all kinds of stuff, not just costuming related. If you have a harbor freight near you, you can get a fairly cheap rotary tool there.

[retrofire[501st]]

Now is the time to relax and take a deep breath. As you tackle this you're going to want to take it a step at a time and be methodical. It's the measure twice cut once adage. Gather your tools and take it a step at a time and take your time. It's better to ask a question than make an expensive mistake so remember to that we're here for you if you need. Looking forward to seeing you get suited up and approved.

[Force Crush[TX]]

Ok, started with the T greeblies.

[Force Crush[TX]]

10:06 p.m. and working on my breastplate pouches. Looking good?

[retrofire[501st]]

Pouches are looking great and they look to be the perfect size.

[Force Crush[TX]]

I'll try to put the velcro on the other side today. Thanks for the feedback!

[Force Crush[TX]]

Ok. Second pouch is ready...I think. Feedback is appreciated. Thanks!

[BananoPower22[501st]]

Try to space the pouches a bit towards the edges of the chest plate and leave about 4 to 5 inches in the middle. While wearing the cummerbund the ribs should be visible.

[Force Crush[TX]]

Chest, back, biceps, forearms and knee velcros are set.

[Force Crush[TX]]

I was planning on cutting the visor from the helmet today. Any advice or tips?

[kaabous[TX]]

My best tip is to go slow and check the sizing and shape often. I used a drill to get some holes started then lexan scissors for the bulk of it. The next time I do it, I would do more of the shaping with rough (80-100 grit) sand paper (or sand blocks are great for it too). I think I tried to get it too close to the necessary size and shape with the scissors and even with curved scissors it was hard not to miscut anything.

 

I'm curious about the nub on the back armor. Can you post a top down pic of that? It looks like they added a spot to rivet the tank top without adding the pandatrooper style bracket. That is awesome!